The P CON MTR relay (transaxle parking lock control relay) is activated by output voltage from the transmission control ECU assembly and supplies power to the shift control actuator assembly (parking lock motor). The transmission control ECU assembly stores this DTC when it detects a malfunction in the P CON MTR relay (transaxle parking lock control relay).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C2303 | When the P CON MTR relay (transaxle parking lock control relay) is off, voltage of transmission control ECU assembly terminal MUA, MVA and MWA are 6 V or more for 0.064 seconds or more. | ·
Transmission control ECU assembly ·
P CON MTR relay (Transaxle parking lock control relay) ·
Wire harness or connector |
Refer to the wiring diagram for DTC C2301 (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>C2301).
It may not be possible to clear the following DTCs using the GTS: DTC C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). In such cases, disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs after the repair.
Disconnect the D2 shift control actuator assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D2-2 (BMA) - Body ground | Power switch off | Below 1 V |
| *a | Front view of wire harness connector
(to Shift Control Actuator Assembly) |
Connect the D2 shift control actuator assembly connector.
OK
NG
Disconnect the A23 transmission control ECU assembly connector.
Disconnect the D2 shift control actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-5 (MUA) or D2-1 (MUA) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A23-2 (MVA) or D2-6 (MVA) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A23-1 (MWA) or D2-7 (MWA) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Transmission Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Shift Control Actuator Assembly) |
Connect the D2 shift control actuator assembly connector.
Connect the A23 transmission control ECU assembly connector.
OK
NG
Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| Auxiliary battery voltage is applied between terminals 1 and 2 | Below 1 Ω |
Reinstall the P CON MTR relay (transaxle parking lock control relay).
OK
NG
Disconnect the A23 transmission control ECU assembly connector.
Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-23 (BMA) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Transmission Control ECU Assembly) |
Reinstall the P CON MTR relay (transaxle parking lock control relay).
Connect the A23 transmission control ECU assembly connector.
OK
NG
Disconnect the D2 shift control actuator assembly connector.
Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D2-2 (BMA) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Shift Control Actuator Assembly) |
Reinstall the P CON MTR relay (transaxle parking lock control relay).
Connect the D2 shift control actuator assembly connector.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG