Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR › from 2013.08
RM2070E _53 Suspension _061919 FRONT SUSPENSION _0301670 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48815E 1.INSTALL FRONT STABILIZER BAR BUSHING LH

a.
C232267E01
1.85,1.202 1.554,0.799 1.554,0.799 0.759,0.799 false 1.78,2.412 1.406,2.412 false 0.558,0.717 0.721,0.866 0.162,0.149 10 *1 1.206,2.337 1.368,2.486 0.162,0.149 10 *2

Install the front stabilizer bar bushing to the outside of the stopper on the front stabilizer bar as shown in the illustration.

Text in Illustration
*1 Stopper
*2 Dust Lip
V100135

Front of the Vehicle
V100136

Inside of the Vehicle

NOTICE:
·

Install the front stabilizer bar bushing so that the dust lips face outward.

·

Install the front stabilizer bar bushing so that the cutouts face rearward.




Hide 48815D 2.INSTALL FRONT STABILIZER BAR BUSHING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 3.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar to the front suspension crossmember sub-assembly so that the identification mark is positioned on the right side of the vehicle.

C239137E01
1.785,1.696 2.812,1.696 false 2.818,1.622 2.986,1.778 0.167,0.155 10 *a

Text in Illustration
*a Identification Mark - -
V100135

Top of the Vehicle
V100136

Front of the Vehicle


Hide 52256 4.INSTALL FRONT SUSPENSION MEMBER FRONT BRACE LH

a.
C236475E03
1.646,1.063 2.26,1.385 2.26,1.385 2.635,1.385 false 1.531,0.385 1.688,0.552 0.156,0.167 10 true A 1.75,0.396 1.906,0.563 0.156,0.167 10 true C 1.021,1.365 1.156,1.542 0.135,0.177 10 true D 1.333,1.604 1.49,1.792 0.156,0.188 10 true B 2.646,1.292 2.813,1.438 0.167,0.146 10 false *a

Install the front suspension member front brace LH with the 4 bolts.

Text in Illustration
*a Protrusion

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:
·

Temporarily tighten bolt A, and then fully tighten the 4 bolts in the order of B, C, D, and A.

·

After installing the front suspension member front brace LH, make sure that the protrusion of the front stabilizer bar bushing is visible.




Hide 52255 5.INSTALL FRONT SUSPENSION MEMBER FRONT BRACE RH

a.
C236476E03
1.802,1.052 1.219,1.323 1.219,1.323 0.771,1.323 true 1.563,0.417 1.698,0.594 0.135,0.177 10 true C 1.802,0.385 1.948,0.563 0.146,0.177 10 true A 2.042,1.573 2.219,1.74 0.177,0.167 10 true B 2.271,1.375 2.396,1.542 0.125,0.167 10 true D 0.604,1.24 0.76,1.385 0.156,0.146 10 false *a

Install the front suspension member front brace RH with the 4 bolts.

Text in Illustration
*a Protrusion

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:
·

Temporarily tighten bolt A, and then fully tighten the 4 bolts in the order of B, C, D, and A.

·

After installing the front suspension member front brace RH, make sure that the protrusion of the front stabilizer bar bushing is visible.




Hide 48069 6.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48069 7.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48810 8.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH with the 2 nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.


Hide 48820B 9.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 10.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48069 12.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 51442E 13.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER

Hide 15.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT