Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM2070E _52 Drivetrain _061917 AXLE AND DIFFERENTIAL _0301660 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY

a.

Secure the steering knuckle between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 2.INSTALL FRONT AXLE ASSEMBLY

a.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
240 N*m (2447 kgf*cm, 177 ft.*lbf)

NOTICE:

When installing the nuts, keep the bolts from rotating.



Hide 43420 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.
C236455E02
2.844,0.635 3.115,0.635 3.115,0.635 3.115,1.635 false 3,0.958 3.115,0.958 false 3.042,1.635 3.208,1.792 0.167,0.156 10 false *a

Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and install the front drive shaft assembly to the front axle hub sub-assembly.

Text in Illustration
*a Matchmark


Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.

Install the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
89 N*m (908 kgf*cm, 66 ft.*lbf)


Hide 7.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 8.TEMPORARILY INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new drive shaft.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a socket wrench (30 mm), while applying the brakes, temporarily install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



Hide 9.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 10.REMOVE FRONT DISC

Hide 11.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 13.INSTALL FRONT DISC

Hide 14.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 47313J 15.INSTALL FRONT FLEXIBLE HOSE

a.

Install the front flexible hose to the steering knuckle with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 89543 16.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.


HINT:

Install the front flexible hose first and then the speed sensor harness bracket.



b.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 17.INSTALL FRONT AXLE SHAFT NUT

a.
C068609

Using a chisel and hammer, stake the front axle shaft nut.


Hide 18.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


b.

Connect the reservoir level switch connector.



Hide 20.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT