Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM2070E _53 Suspension _061921 TIRE PRESSURE MONITORING _0301678 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. DTC Detection Condition Trouble Area
B1247 In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

C355819E09
1.333,0.5 1.583,0.698 0.25,0.198 10 false IG 1.198,1.063 1.625,1.26 0.427,0.198 10 false RDA 1.198,1.563 1.594,1.76 0.396,0.198 10 false PRG 1.188,2.135 1.646,2.333 0.458,0.198 10 false GND 1.604,0.406 2.021,0.656 0.417,0.25 10 false 1 1.615,0.979 2.031,1.229 0.417,0.25 10 false 4 1.615,1.469 2.031,1.719 0.417,0.25 10 false 5 1.583,2.01 1.938,2.198 0.354,0.188 10 false 12 2.25,0.677 3.177,0.958 0.927,0.281 10 false ECU-IG NO. 1 3.885,0.521 5.385,1.021 1.5,0.5 10 false from IG Circuit 5.417,1.979 5.813,2.146 0.396,0.167 10 false L201 5.417,2.156 7.073,2.885 1.656,0.729 10 false Main Body ECU (Multiplex Network Body ECU) 5.396,0.979 5.708,1.146 0.313,0.167 10 false 16 5.469,1.49 5.75,1.688 0.281,0.198 10 false 4 5.688,1.083 6.073,1.24 0.385,0.156 10 false RDA 5.688,1.583 6.031,1.75 0.344,0.167 10 false PRG 0.344,2.729 0.615,3.01 0.271,0.281 10 false R42 0.344,2.896 1.74,3.615 1.396,0.719 10 false Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the R42 tire pressure warning ECU and receiver connector.


b.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-4 (RDA) - L201-16 (RDA) Always Below 1 Ω
R42-4 (RDA) or L201-16 (RDA) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.
U191135E02
1.24,1.208 0.833,1.698 0.833,1.698 0.833,1.813 false 2.198,1.365 2.625,1.271 2.625,1.271 2.74,1.271 false 0.385,1.135 0.719,1.302 0.333,0.167 10 false R42 0.135,0.104 0.344,0.292 0.208,0.188 10 false *a 0.771,1.823 0.99,2.021 0.219,0.198 10 false IG 2.792,1.188 3.135,1.354 0.344,0.167 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R42-1 (IG) - Body ground Power switch on (IG) 10 to 16 V



Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (B1247)
4.CHECK DTC OUTPUT (B1247)

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1247 is not output.




OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)