Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2016.05
RM2070E _53 Suspension _061922 TIRE / WHEEL _0301681 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure:
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
205/60R16 92V 250 (2.5, 36)
240 (2.4, 35)*1
250 (2.5, 36)
230 (2.3, 33)*1
215/50R17 91V 230 (2.3, 33) 230 (2.3, 33)


*1: for Australia

i.

Perform initialization (w/ Tire Pressure Warning System) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).


ii.

Tire pressure adjustment method when warm (w/ Tire Pressure Warning System).

1.

Turn the power switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG).

4.

Turn the GTS on.

5.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

6.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

7.

Perform initialization and check that initialization completes (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).

8.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

9.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

10.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


11.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


NOTICE:
for ECE-R64 Type:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)



Hide 2. ROTATE TIRES

a.
C163156

Rotate the tires as shown in the illustration.

Text in Illustration
V100135

Front


b.

Perform initialization (w/ Tire Pressure Warning System) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).


Hide 3.INSPECT AND ADJUST WHEEL BALANCE

a.
C144018E08
2.044,3.632 2.258,3.800 0.214,0.167 10 (A)

Inspect and adjust the off-the-car balance.

Maximum Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the balance weight.

·

Adhere a stick-on type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight securely with your finger to adhere it to the desired position.

·

Do not reuse balance weights.



HINT:

The inner side balance weight should be installed by clipping it to the rim.



Hide 4.INSPECT FRONT AXLE HUB AND BEARING

Hide 5.INSPECT REAR AXLE HUB AND BEARING