The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.
The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) will be output.
The DTCs will be also output when the calibration has not been completed.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1210/36 | - | Yaw rate sensor zero point calibration is incomplete. | ·
Zero point calibration undone ·
Yaw rate sensor (Airbag ECU assembly) ·
Brake booster with master cylinder (Skid control ECU) (Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.) |
| C1336/98 | - | Either of the following is detected:
1.
The vehicle is driven normally without zero point calibration completed. 2.
After completing zero point calibration, zero point voltage of the sensor is not within the range of 2.38 to 2.62 V. |
·
Zero point calibration undone ·
Acceleration sensor (Airbag ECU assembly) ·
Brake booster with master cylinder (Skid control ECU) (Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.) |
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).
When U0123/62 and/or U0124/95 is output together with C1210/36 and/or C1336/98, inspect and repair trouble areas indicated by U0123/62 and/or U0124/95 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).
Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).
NEXT
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1210/36 and/or C1336/98) are output | A |
| DTCs (C1210/36 and C1336/98) are not output | B |
The DTCs are recorded because zero point calibration has not been completed.
End the procedure because the same DTCs are not recorded after completion of zero point calibration.
A
B
Turn the power switch off (lock).
Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).
The airbag ECU assembly is tightened to the specified torque.
The airbag ECU assembly is not tilted.
OK
NG
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION)
Replace the yaw rate and acceleration sensor (airbag ECU assembly) (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).
Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1210/36 and/or C1336/98) are output (for LHD) | A |
| DTCs (C1210/36 and/or C1336/98) are output (for RHD) | B |
| DTCs (C1210/36 and C1336/98) are not output | C |
A
B
C