Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.08–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1231/31  Steering Angle Sensor Circuit Malfunction  


DESCRIPTION

The skid control ECU inputs steering angle sensor signals via the CAN communication system. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126/63 (Lost Communication with Steering Angle Sensor Module) is output.

DTC Code INF Code DTC Detection Condition Trouble Area
C1231/31 701 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction). Steering angle sensor internal malfunction
↑ 702 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction). ↑
↑ 703 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction). ↑

WIRING DIAGRAM

C167662E90
0.156,4.021 0.667,4.24 0.51,0.219 10 false L51 0.896,3.281 1.208,3.448 0.313,0.167 10 false ESS 0.792,0.656 1.198,0.823 0.406,0.167 10 false CANL 0.792,1.24 1.208,1.406 0.417,0.167 10 false CANH 0.896,1.927 1.188,2.094 0.292,0.167 10 false BAT 1.021,2.604 1.219,2.771 0.198,0.167 10 false IG 1.281,0.51 1.479,0.698 0.198,0.188 10 false 3 1.281,1.083 1.469,1.271 0.188,0.188 10 false 4 1.281,1.802 1.406,1.99 0.125,0.188 10 false 6 1.281,2.479 1.385,2.667 0.104,0.188 10 false 5 1.281,3.135 1.385,3.323 0.104,0.188 10 false 2 2.26,2.094 2.76,2.25 0.5,0.156 10 false ECU-B 2.01,2.771 2.927,2.927 0.917,0.156 10 false ECU-IG NO. 2 3.906,1.948 5.292,2.115 1.385,0.167 10 false from Auxiliary Battery 3.906,2.615 5.344,2.781 1.438,0.167 10 false from IG1 NO. 1 Relay 5.771,1.104 5.979,1.281 0.208,0.177 10 false 37 5.563,4.031 5.833,4.177 0.271,0.146 10 false A58 6.042,0.656 6.469,0.833 0.427,0.177 10 false CA1L 6.042,1.24 6.469,1.417 0.427,0.177 10 false CA1H 5.76,0.51 5.938,0.688 0.177,0.177 10 false 38 5.885,4.031 7.094,4.406 1.208,0.375 10 false Brake Booster with Master Cylinder 0.448,4.021 2.021,4.25 1.573,0.229 10 false Steering Angle Sensor

CAUTION / NOTICE / HINT

HINT:
·

When U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0126/63 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).

·

When the speed sensor or the yaw rate and acceleration sensor are malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).


d.

Drive the vehicle and turn the steering wheel to the right and left at the speed of 35 km/h (22 mph) and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1231/31) is output A
CAN communication system DTC is output B
Speed sensor and/or yaw rate and acceleration sensor DTC is output C
DTC (C1231/31) is not output D


HINT:
·

When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.

·

If there is a malfunction in the speed sensor or the yaw rate and acceleration sensor, an abnormal value may be output although the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these two sensors and inspect the steering angle sensor.





A

2.INSPECT STEERING ANGLE SENSOR (POWER SOURCE TERMINAL)

B

C

D

2.INSPECT STEERING ANGLE SENSOR (POWER SOURCE TERMINAL)
a.
U191146E02
2.385,2.333 2.833,1.354 true 2.094,2.323 1.469,1.375 true 0.438,1.292 0.781,1.448 0.344,0.156 10 false L51 0.198,0.208 0.417,0.365 0.219,0.156 10 false *a 2.885,1.25 3.188,1.406 0.302,0.156 10 false BAT 1.292,1.281 1.521,1.438 0.229,0.156 10 false IG

Turn the power switch off (lock).


b.

Remove the steering wheel and the column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the steering angle sensor connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L51-5 (IG) - Body ground Power switch on (IG) 11 to 14 V
L51-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

3.INSPECT STEERING ANGLE SENSOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.INSPECT STEERING ANGLE SENSOR (GROUND TERMINAL)
a.
U154706E03
1.396,2.323 1.896,1.156 true 0.375,1.281 0.719,1.438 0.344,0.156 10 false L51 0.198,0.208 0.417,0.365 0.219,0.156 10 false *a 1.76,0.979 2.063,1.135 0.302,0.156 10 false ESS

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L51-2 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)