Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.11–2017.12
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in a speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the power switch from off (lock) to on (IG).

WIRING DIAGRAM

C167369E35
0.415,2.93 0.718,3.088 0.303,0.157 10 L61 0.94,1.791 1.195,1.953 0.255,0.162 10 CG 0.954,0.909 1.209,1.071 0.255,0.162 10 TS 1.238,0.815 1.435,0.971 0.198,0.156 10 12 1.259,1.694 1.456,1.850 0.198,0.156 10 4 5.559,2.924 5.842,3.073 0.283,0.149 10 A58 6.029,0.906 6.230,1.055 0.201,0.149 10 TS 5.829,0.808 6.002,0.957 0.173,0.149 10 4 5.878,2.924 7.086,3.267 1.208,0.343 10 Brake Booster with Master Cylinder 0.73,2.93 1.116,3.088 0.386,0.157 10 DLC3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TS of DLC3)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-4 (TS) - L61-12 (TS) Always Below 1 Ω
A58-4 (TS) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U154737E01
0.263,0.249 0.446,0.419 0.184,0.170 10 *a 2.273,0.811 2.513,0.980 0.239,0.170 10 CG 0.297,1.039 0.627,1.190 0.330,0.151 10 L61 1.669,1.957 2.396,1.014 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR