Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.11–2017.12
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1391/69  Accumulator Leak Malfunction  


DESCRIPTION

The DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator or brake booster pump. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC Code INF Code DTC Detection Condition Trouble Area
C1391/69 351 Either of the following is detected:
1.

Accumulator pressure sensor input does not increase before braking or while the pump motor is operating.

2.

Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating.


·

Brake fluid leaks

·

Brake booster with master cylinder (Brake actuator)

(Malfunctioning internal seal, low gas pressure in accumulator, etc.)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK FOR FLUID LEAK
a.

Check that there is no fluid leaks in the brake line between the brake actuator and the wheel cylinder which is indicated by DTCs.


b.

Check that the brake is not dragging.

OK:

There is no fluid leaks or dragging.




OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE APPLICABLE PART

2.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1391/69) is output A
DTC (C1391/69) is not output (for LHD) B
DTC (C1391/69) is not output (for RHD) C




A

3.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

3.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
a.

Turn the power switch off (lock).


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Park (P) is selected.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System


e.

Perform the Active Test of the solenoid using the GTS.



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

g.

Check that the output value of the wheel cylinder does not increase.

OK:

The output value of the wheel cylinder does not increase.


HINT:

If any output value increases, there may be brake fluid leaks in the brake actuator.


Result:
Result Proceed to
The output value of the wheel cylinder increases A
The output values of the wheel cylinders do not increase B




A

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
a.

Replace the brake booster with master cylinder (brake actuator) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL for LHD, or Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL for RHD).



NEXT