The skid control ECU receives the signals from the power management control ECU, steering angle sensor, and yaw rate and acceleration sensor via the CAN communication system.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0073/94 | 461 | Either of the following is detected:
1.
Yaw rate and acceleration sensor communication is disabled for 1 second or more. 2.
Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. |
·
CAN communication line (V bus) ·
Yaw rate and acceleration sensor ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 462 | Either of the following is detected:
1.
Steering angle sensor communication is disabled for 1 second or more. 2.
Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. |
·
CAN communication line (V bus) ·
Steering angle sensor ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 463
464 |
Bus off occurs once or more per 0.1 seconds 10 times repeatedly. | ·
CAN communication line ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 465
466 |
Sending does not complete within 5 seconds after data is output from the skid control ECU. | ↑ |
| U0123/62 | 731 | Yaw rate sensor communication is disabled for 1 second or more. | ·
CAN communication line (V bus) ·
Yaw rate and acceleration sensor ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 732 | Yaw rate sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. | ↑ |
| U0124/95 | 591 | Acceleration sensor communication is disabled for 1 second or more. | ·
CAN communication line (V bus) ·
Yaw rate and acceleration sensor ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 592 | Acceleration sensor communication is disabled once per 5 seconds 10 times or more within 60 seconds. | ↑ |
| U0126/63 | 741 | Steering angle sensor communication is disabled for 1 second or more. | ·
CAN communication line (V bus) ·
Steering angle sensor ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 742 | Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. | ↑ |
| U0293/59 | 411
412 413 |
Either of the following is detected:
1.
With the IG2 terminal voltage 9.5 V or more, data from the power management control ECU cannot be received for 2 seconds or more. 2.
With the IG2 terminal voltage 9.5 V or more, data from the power management control ECU cannot be received once or more within 5 seconds occur 10 times in succession. |
·
CAN communication line (Sub bus 12) ·
Power management control ECU ·
Brake booster with master cylinder (Skid control ECU) |
for LHD
for RHD
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Yaw Rate Open | Yaw rate sensor open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Steering Open | Steering angle sensor open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| HV Communication Open | Hybrid vehicle communication open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Result | Proceed to |
|---|---|
| There is a constant open circuit | A |
| There are no momentary interruptions | B |
| There are momentary interruptions | C |
Perform the above inspection before removing any sensor or connector.
A
B
C
Turn the power switch off (lock).
Check if each sensor and ECU connector are securely connected.
Each sensor and ECU connector are securely connected.
OK
NG
Turn the power switch off (lock).
Record the output DTCs (for ABS, VSC, electronically controlled brake system, and/or CAN communication system) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR for ABS, VSC and/or electronically controlled brake system, or Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM for CAN communication system).
If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC (ABS, VSC and/or electronically controlled brake system DTC) is output | B |
| DTC (CAN communication system DTC) is output | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the power switch off (lock).
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and each sensor or ECU (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
Check that there are no momentary interruptions.
NEXT
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
Check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
If ABS, VSC and/or electronically controlled brake system DTCs are output, record them (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC (ABS, VSC and/or electronically controlled brake system DTC) is output | B |
| DTC (CAN communication system DTC) is output | C |
The CAN communication system must be normal when repairing each sensor DTC (for ABS, VSC and/or electronically controlled brake system).
A
B
C