When a fluid level drop in the master cylinder reservoir is detected, the signal is input to the skid control ECU.
If the DTC for the fluid level drop is memorized, the warning will be canceled and the DTC will not be stored when the fluid level returns to normal.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1202/68 | 371 | An open is detected in the switch signal circuit for 2 seconds or more. | ·
Brake master cylinder reservoir (Brake fluid level warning switch) internal open circuit ·
Open in wire harness ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | - | The reservoir level remains low. | ·
Low brake fluid level ·
Brake fluid leaks ·
Brake master cylinder reservoir (Brake fluid level warning switch) internal short circuit ·
Short in wire harness ·
Brake disc rotor excessive wear ·
Brake booster with master cylinder (Skid control ECU) |
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
When releasing the parking brake, chock the wheels for safety.
Check that the brake fluid level is sufficient.
Brake fluid level is sufficient.
If the fluid level is low, check for fluid leaks, and repair as necessary.
Check for brake fluid leaks (Connection between the brake booster pump, brake master cylinder reservoir and brake booster with master cylinder, and the brake booster with master cylinder and wheel cylinders).
If no leaks exist, add and adjust fluid using the GTS (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION).
Check that the trouble code is not output again (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Check that there are no leaks from the connections between the brake booster pump and brake booster with master cylinder.
As a visual check is very difficult, perform the check with the following procedure.
Bleed the air from the brake systems (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Accumulator Sensor | Accumulator pressure sensor / Min.: 0.00 V, Max.: 5.00 V | Specified value: 2.90 to 4.20 V | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
Wait for 30 seconds without depressing the brake pedal.
Check that the accumulator pressure sensor output values change is within the specified range.
Accumulator pressure sensor output values change is within 0.55 V.
OK
NG
Turn the power switch off (lock).
Remove the reservoir filler cap.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the level of brake fluid.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Brake fluid level warning switch OFF (Float up) | 1.84 to 2.16 kΩ |
| 1 (+) - 2 (E) | Brake fluid level warning switch ON (Float down) | Below 1 Ω |
| *a | Component without harness connected
(Brake Fluid Level Warning Switch) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-36 (LBL) - A32-1 (+) | Always | Below 1 Ω |
| A58-36 (LBL) - Body ground | Always | 10 kΩ or higher |
| A32-2 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Reconnect the skid control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-1 (+) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Brake Fluid Level Warning Switch) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Reconnect the brake fluid level warning switch connector.
Disconnect the brake pedal stroke sensor connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. Check the brake line pressure vibration caused due to uneven wear of the disc according to brake pedal vibration.
Brake pedal does not vibrate during braking.
An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
The brake pedal does not kick back due to wheel cylinder piston vibration during electronically controlled brake system control.
If the brake pedal stroke sensor connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
The Active Test does not prohibit electronically controlled brake system control when driving the vehicle, so disconnect the stroke sensor connector before continuing with inspection.
Disc uneven wear can be checked by measuring the disc thickness variation (See page Brake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION for front, or Brake>BRAKE (REAR)>REAR BRAKE>INSPECTION for rear).
OK
NG
Reconnect the brake pedal stroke sensor connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC (C1202/68) is not output | A |
| DTC (C1202/68) is output (for LHD) | B |
| DTC (C1202/68) is output (for RHD) | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C