The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
DTCs C1271/71 and C1272/72 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1464/31 | 501 | While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor RH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 502 | A malfunction occurs in 2 or more wheels. | ↑ |
| ↑ | 503 | An open is detected in the speed sensor signal circuit for 0.05 seconds or more. | ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor RH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 504 | Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor RH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 506 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more. | ·
Open or short in wire harness ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 507 | While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor RH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 508 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more. | ·
Open or short in wire harness ·
Brake booster with master cylinder (Skid control ECU) |
| C1465/32 | 511 | While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor LH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 512 | A malfunction occurs in 2 or more wheels. | ↑ |
| ↑ | 513 | An open is detected in the speed sensor signal circuit for 0.05 seconds or more. | ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor LH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 514 | Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor LH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 516 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more. | ·
Open or short in wire harness ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 517 | While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Front speed sensor LH ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 518 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more. | ·
Open or short in wire harness ·
Brake booster with master cylinder (Skid control ECU) |
| C1271/71
C1272/72 |
- | Detected only during Test Mode. | ·
Front speed sensor RH/LH ·
Sensor installation ·
Speed sensor rotor |
DTCs C1464/31 and C1271/71 are for the front speed sensor RH.
DTCs C1465/32 and C1272/72 are for the front speed sensor LH.
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| FL Speed Open | Front speed sensor LH open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
OK
NG
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | Front speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check that the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
The speed value output from the speed sensor displayed on the GTS is the similar speed as indicated on the speedometer.
OK
NG
Turn the power switch off (lock).
Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
All Test Mode DTCs are cleared.
OK
NG
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1464/31 and C1465/32) are not output | A |
| DTCs (C1464/31 and/or C1465/32) are output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the power switch off (lock).
Check the speed sensor installation.
There is no clearance between the sensor and the front steering knuckle.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
OK
NG
Remove the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor tip.
The sensor tip is free of scratches, oil, and foreign matter.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
OK
NG
Install the front speed sensor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-18 (FR+) - A34-2 (FR+) | Always | Below 1 Ω |
| A58-18 (FR+) - Body ground | Always | 10 kΩ or higher |
| A58-5 (FR-) - A34-1 (FR-) | Always | Below 1 Ω |
| A58-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-31 (FL+) - A15-2 (FL+) | Always | Below 1 Ω |
| A58-31 (FL+) - Body ground | Always | 10 kΩ or higher |
| A58-32 (FL-) - A15-1 (FL-) | Always | Below 1 Ω |
| A58-32 (FL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-2 (FR+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-2 (FL+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Reconnect the front speed sensor connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1464/31 and/or C1465/32) are output | A |
| DTCs (C1464/31 and C1465/32) are not output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off (lock).
Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1464/31 and/or C1465/32) are output | A |
| DTCs (C1464/31 and C1465/32) are not output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
Turn the power switch off (lock).
Replace the front axle hub sub-assembly (front speed sensor rotor) (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).
The front speed sensor rotor is incorporated into the front axle hub sub-assembly.
If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1464/31 and/or C1465/32) are output (for LHD) | A |
| DTCs (C1464/31 and/or C1465/32) are output (for RHD) | B |
| DTCs (C1464/31 and C1465/32) are not output | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
C