Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2016.05–2017.12
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1466/33  Rear Speed Sensor RH Circuit  C1467/34  Rear Speed Sensor LH Circuit  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.

DTCs C1273/73 and C1274/74 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273/73 and C1274/74 are output only in Test Mode.

C334047E03
1.583,0.865 1.583,0.354 1.583,0.354 1.76,0.354 false 1.802,0.271 2.969,0.563 1.167,0.292 10 false Speed Sensor 0.948,2.188 2.49,2.521 1.542,0.333 10 false Speed Sensor Rotor 4.031,2.083 4.802,2.281 0.771,0.198 10 false Low speed 4.99,2.104 5.854,2.344 0.865,0.24 10 false High speed 6.042,1.625 6.813,1.823 0.771,0.198 10 false 0.7V 6.031,1.26 6.802,1.458 0.771,0.198 10 false 1.4V

DTC Code INF Code DTC Detection Condition Trouble Area
C1466/33 521 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Brake booster with master cylinder (Skid control ECU)


↑ 522 A malfunction occurs in 2 or more wheels. ↑
↑ 523 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Brake booster with master cylinder (Skid control ECU)


↑ 524 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Brake booster with master cylinder (Skid control ECU)


↑ 526 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Brake booster with master cylinder (Skid control ECU)


↑ 527 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Brake booster with master cylinder (Skid control ECU)


↑ 528 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Brake booster with master cylinder (Skid control ECU)


C1467/34 531 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Brake booster with master cylinder (Skid control ECU)


↑ 532 A malfunction occurs in 2 or more wheels. ↑
↑ 533 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Brake booster with master cylinder (Skid control ECU)


↑ 534 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Brake booster with master cylinder (Skid control ECU)


↑ 536 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Brake booster with master cylinder (Skid control ECU)


↑ 537 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Brake booster with master cylinder (Skid control ECU)


↑ 538 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Brake booster with master cylinder (Skid control ECU)


C1273/73
C1274/74
- Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Speed sensor rotor



HINT:
·

DTCs C1466/33 and C1273/73 are for the rear speed sensor RH.

·

DTCs C1467/34 and C1274/74 are for the rear speed sensor LH.



WIRING DIAGRAM

C220952E21
0.927,1.427 2.448,1.594 1.521,0.167 10 false Rear Speed Sensor RH 2.229,0.938 2.344,1.104 0.115,0.167 10 false 1 1.063,0.938 1.177,1.104 0.115,0.167 10 false 2 0.938,3.375 2.458,3.542 1.521,0.167 10 false Rear Speed Sensor LH 2.229,2.875 2.344,3.042 0.115,0.167 10 false 1 1.063,2.896 1.177,3.063 0.115,0.167 10 false 2 5.823,4 7.052,4.385 1.229,0.385 10 false Brake Booster with Master Cylinder 5.781,1.031 5.958,1.177 0.177,0.146 10 false 9 5.958,0.583 6.281,0.729 0.323,0.146 10 false RR+ 5.719,0.479 5.896,0.625 0.177,0.146 10 false 22 5.938,1.146 6.229,1.292 0.292,0.146 10 false RR- 5.771,3 6,3.146 0.229,0.146 10 false 7 5.948,2.542 6.302,2.688 0.354,0.146 10 false RL+ 5.719,2.427 5.896,2.573 0.177,0.146 10 false 20 5.958,3.094 6.208,3.24 0.25,0.146 10 false RL- 1.01,1.125 1.302,1.292 0.292,0.167 10 false z2 4.229,1.51 4.896,1.677 0.667,0.167 10 false Shielded 4.26,3.49 4.927,3.656 0.667,0.167 10 false Shielded 5.49,4.01 5.792,4.156 0.302,0.146 10 false A58 1.344,1.135 1.667,1.281 0.323,0.146 10 false RR+ 1.771,1.135 2.063,1.281 0.292,0.146 10 false RR- 1.344,3.073 1.698,3.219 0.354,0.146 10 false RL+ 1.802,3.073 2.052,3.219 0.25,0.146 10 false RL- 2.99,0.375 3.104,0.542 0.115,0.167 10 false 1 2.99,0.938 3.104,1.104 0.115,0.167 10 false 2 2.198,1.125 2.49,1.292 0.292,0.167 10 false z2 0.677,1.74 2.542,1.906 1.865,0.167 10 false Skid Control Sensor Wire RH 2.917,0.563 3.313,0.729 0.396,0.167 10 false zS1 2.906,1.125 3.302,1.292 0.396,0.167 10 false zS1 1.01,3.073 1.26,3.24 0.25,0.167 10 false z1 2.188,3.073 2.438,3.24 0.25,0.167 10 false z1 0.677,3.667 2.583,3.833 1.906,0.167 10 false Skid Control Sensor Wire LH 2.99,2.313 3.104,2.479 0.115,0.167 10 false 1 2.99,2.875 3.104,3.042 0.115,0.167 10 false 2 2.906,2.51 3.229,2.677 0.323,0.167 10 false zR1 2.917,3.073 3.26,3.24 0.344,0.167 10 false zR1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


b.

Check that the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is the similar speed as indicated on the speedometer.




OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off (lock).


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.




OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1466/33 and C1467/34) are not output A
DTCs (C1466/33 and/or C1467/34) are output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

10.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144931E25
0.99,1.542 1.24,0.823 1.24,0.823 1.365,0.823 false 0.156,0.115 1.563,0.323 1.406,0.208 10 false Rear Speed Sensor: 1.396,0.729 2.281,0.917 0.885,0.188 10 false No clearance 0.885,2.813 1.146,3 0.26,0.188 10 false OK 2.323,2.813 2.583,3 0.26,0.188 10 false NG

Turn the power switch off (lock).


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.




OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)
a.
U154691E01
0.224,0.2 0.428,0.351 0.203,0.151 10 *a 1.181,2.794 1.388,2.950 0.207,0.155 10 *b 1.095,0.843 1.334,0.986 0.239,0.143 10 z2 1.446,0.843 1.649,1.006 0.202,0.163 10 *A 2.634,2.554 2.841,2.709 0.207,0.155 10 *c 2.439,1.049 2.742,1.212 0.303,0.163 10 zS1 2.83,1.049 3.046,1.212 0.216,0.163 10 *A 1.095,1.138 1.334,1.281 0.239,0.143 10 z1 1.446,1.138 1.649,1.301 0.202,0.163 10 *B 2.439,1.345 2.733,1.508 0.294,0.163 10 zR1 2.83,1.345 3.046,1.508 0.216,0.163 10 *B

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the rear speed sensor connector and the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
z2-2 - zS1-1 Always Below 1 Ω
z2-2 - zS1-2 Always 10 kΩ or higher
z2-2 - Body ground Always 10 kΩ or higher
z2-1 - zS1-2 Always Below 1 Ω
z2-1 - zS1-1 Always 10 kΩ or higher
z2-1 - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
z1-2 - zR1-1 Always Below 1 Ω
z1-2 - zR1-2 Always 10 kΩ or higher
z1-2 - Body ground Always 10 kΩ or higher
z1-1 - zR1-2 Always Below 1 Ω
z1-1 - zR1-1 Always 10 kΩ or higher
z1-1 - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A58-22 (RR+) - zS1-1 (RR+) Always Below 1 Ω
A58-22 (RR+) - Body ground Always 10 kΩ or higher
A58-9 (RR-) - zS1-2 (RR-) Always Below 1 Ω
A58-9 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A58-20 (RL+) - zR1-1 (RL+) Always Below 1 Ω
A58-20 (RL+) - Body ground Always 10 kΩ or higher
A58-7 (RL-) - zR1-2 (RL-) Always Below 1 Ω
A58-7 (RL-) - Body ground Always 10 kΩ or higher




OK

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
U154775E03
2.625,2.052 2.865,2.521 false 0.323,0.25 0.563,0.427 0.24,0.177 10 false *a 1.219,2.563 1.573,2.708 0.354,0.146 10 false RR+ 2.719,2.542 3.01,2.688 0.292,0.146 10 false RL+ 0.313,1.073 0.656,1.25 0.344,0.177 10 false zS1 1.74,1.073 2.01,1.219 0.271,0.146 10 false zR1

Reconnect the skid control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
zS1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH:
Tester Connection Condition Specified Condition
zR1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Sensor Wire)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

9.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

9.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Reconnect the rear speed sensor connector and the skid control sensor wire.



d.

Turn the power switch on (ready).


e.

Perform a road test.


f.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1466/33 and/or C1467/34) are output A
DTCs (C1466/33 and C1467/34) are not output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

10.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR

B

10.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR
a.

Turn the power switch off (lock).


b.

Replace the rear speed sensor and the rear axle hub and bearing assembly (rear speed sensor rotor) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Perform a road test.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1466/33 and/or C1467/34) are output (for LHD) A
DTCs (C1466/33 and/or C1467/34) are output (for RHD) B
DTCs (C1466/33 and C1467/34) are not output C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

END