Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM › from 2014.11
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301692 BRAKE SYSTEM G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

A DTC may be stored during the inspection procedure. Be sure to clear the DTCs and check that a normal system code is output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the GTS.

i.
C236034E01
1.188,0.258 1.341,0.406 0.153,0.148 10 *1 1.524,0.347 1.356,0.347 false 2.45,0.258 2.602,0.406 0.153,0.148 10 *2 2.786,0.347 2.618,0.347 false 0.827,0.258 0.979,0.406 0.153,0.148 10 *2 0.825,0.347 0.657,0.347 false 0.61,2.788 0.762,2.936 0.153,0.148 10 *3 2.846,2.476 2.999,2.624 0.153,0.148 10 *3 3.213,2.55 3.014,2.55 false 0.431,2.873 0.61,2.873 false

Set a pedal effort gauge and SST (LSPV gauge and No. 1 nipple).

SST
09709-29018  (09709-00060)

Text in Illustration
*1 Pedal Effort Gauge
*2 SST (LSPV Gauge)
*3 SST (No. 1 Nipple)


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.


iv.

Bleed air from SST (LSPV gauge) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).



c.

Inspect wheel cylinder pressure sensor and regulator pressure sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test / Power Supply Air Bleeding Pattern 1.


ii.

Select "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output".


iii.

Check the value output from "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output" by depressing the brake pedal.

Standard Result:
Pedal Effort
N (kgf, lbf)
Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
50 (5, 11.2) 0.57 to 1.37 0.31 to 4.31 (3.2 to 43.9, 45 to 625) 0.31 to 4.31 (3.2 to 43.9, 45 to 625)
100 (10, 22.5) 1.50 to 2.30 4.88 to 8.88 (49.8 to 90.5, 708 to 1288) 4.88 to 8.88 (49.8 to 90.5, 708 to 1288)
150 (15, 33.7) 2.44 to 3.24 9.45 to 13.45 (96.4 to 137.1, 1371 to 1950) 9.45 to 13.45 (96.4 to 137.1, 1371 to 1950)
200 (20, 45.0) 3.37 to 4.17 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612) 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612)


Standard Result:
Pedal Effort
N (kgf, lbf)
Wheel Cylinder Pressure Sensor
(V)
Front Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Front Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
50 (5, 11.2) 0.51 to 1.31 0.00 to 3.98 (0.0 to 40.5, 0 to 577) 0.00 to 3.98 (0.0 to 40.5, 0 to 577)
100 (10, 22.5) 1.30 to 2.10 3.89 to 7.89 (39.7 to 80.4, 565 to 1144) 3.89 to 7.89 (39.7 to 80.4, 565 to 1144)
150 (15, 33.7) 2.10 to 2.90 7.80 to 11.80 (79.6 to 120.3, 1132 to 1711) 7.80 to 11.80 (79.6 to 120.3, 1132 to 1711)
200 (20, 45.0) 2.89 to 3.69 11.68 to 15.68 (119.2 to 159.8, 1695 to 2274) 11.68 to 15.68 (119.2 to 159.8, 1695 to 2274)



iv.

After inspection, turn "Power Supply Air Bleeding Pattern 1" off.



d.

Remove pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed brake line (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).



e.

Inspect accumulator sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Accumulator Sensor".


ii.

Depress the brake pedal 4 or 5 times and operate the booster pump motor.


iii.

After confirming that the booster pump motor stops, check the output voltage.

Standard voltage:

2.9 to 4.2 V




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.



ii.
C256201E01
2.313,1.263 2.467,1.405 0.154,0.142 10 *a 2.313,1.545 2.467,1.687 0.154,0.142 10 *b 2.827,1.128 2.606,1.35 2.606,1.35 2.483,1.35 false 2.832,1.388 2.582,1.638 2.582,1.638 2.483,1.638 false

Adjust the brake fluid level in the reservoir between MIN line and fluid level support line.

Text in Illustration
*a Fluid Level Support Line
*b MIN Line


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility / Zero Down.

NOTICE:

Go to the next step without turning the power switch off.



iv.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Wheel Cylinder Pressure Sensor", "Stroke Sensor" and "Stroke Sensor 2".


v.

Check the value output from "Wheel Cylinder Pressure Sensor", "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort
N (kgf, lbf)
Wheel Cylinder Pressure Sensor
(V)
Stroke Sensor
(V)
Stroke Sensor 2
(V)
200 (20, 45.0) 0.50 to 1.30 0.97 to 1.67 3.33 to 4.03
500 (51, 112.4) 1.10 to 1.90 1.15 to 1.85 3.15 to 3.85



vi.

Turn the power switch off to finish "Zero Down".


vii.

Turn the power switch on and wait for 20 seconds, then enter the following menus: Chassis / ABS/VSC/TRC / Data List "Accumulator Sensor", and check the output voltage.

Standard voltage:

2.9 to 4.2 V




Hide 3.INSPECT STROKE SIMULATOR

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor" and "Stroke Sensor 2".


iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the value output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort
N (kgf, lbf)
Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 (5 11.2) 1.07 to 1.77 3.23 to 3.93
100 (10, 22.4) 1.25 to 1.95 3.05 to 3.75
150 (15, 34.0) 1.35 to 2.05 2.95 to 3.65