Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD) › from 2014.11
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301695 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Turn back the dash silencer from the slit provided on the dash silencer.


iii.
C238455E01
2.842,0.92 3.001,1.064 0.159,0.144 10 *1 2.446,1 2.842,1 false 1.375,1.808 1.534,1.952 0.159,0.144 10 *2 1.469,1.34 1.469,1.808 false 0.822,3.851 0.981,3.995 0.159,0.144 10 *3 2.84,3.935 2.999,4.079 0.159,0.144 10 *a 1.58,3.601 1.253,3.929 1.253,3.929 1.003,3.929 false

Measure the shortest distance between the brake pedal surface and floor panel.

Text in Illustration
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Floor Panel
*a Brake Pedal Height

Brake pedal height from floor panel:

126.3 to 136.3 mm (4.98 to 5.36 in.)




b.

Adjust the brake pedal height.

i.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.


iv.

Tighten the clevis lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install and adjust the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).



Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

Inspect the brake pedal stroke sensor assembly.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".


v.

Read the stroke sensor value without the brake pedal depressed.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V


If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.



b.

Adjust the brake pedal stroke sensor assembly.

i.

Remove the No. 1 instrument panel under cover sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL).


ii.
C238475

Loosen the 2 nuts.


iii.
C238474

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V



iv.
C238475E03
0.583,0.458 0.708,0.635 0.125,0.177 10 true 1 1.177,1.74 1.271,1.885 0.094,0.146 10 false 2

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Do not depress the brake pedal after turning the power switch on (IG).

·

Tighten the 2 nuts in the order shown in the illustration.




v.

Turn the GTS off and turn the power switch off.


vi.

Disconnect the GTS.


vii.

Install the No. 1 instrument panel under cover sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).



Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708E22
2.177,1.573 2.344,1.75 0.167,0.177 10 false *a

Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Text in Illustration
*a Brake Pedal Free Play

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION). If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:

Measure the distance at the same point used for the brake pedal height inspection.


a.

Release the parking brake.


b.

With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance.

Pedal reserve distance from the floor panel at 196 N (20 kgf, 44.1 lbf):

More than 74.8 mm (2.94 in.)


If the distance is not as specified, troubleshoot the brake system (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).


Hide 5. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE