Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM2070E _54 Brake _061925 BRAKE (FRONT) _0301701 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C210926E01
1.938,1.084 2.549,1.1 2.549,1.1 1.966,1.149 false 2.57,1.01 2.734,1.160 0.164,0.150 10 *a

Align the matchmarks of the disc and axle hub, and install the front disc.

Text in Illustration
*a Matchmark

NOTICE:

When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



Hide 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.
C210925

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C211756

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.
C210923

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING

a.
C211757

Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 2 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.


Hide 47715D 5.INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.
C211758

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.
C210922

Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 47715A 6.INSTALL FRONT NO. 1 DISC BRAKE CYLINDER SLIDE PIN

a.
C211759

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 1 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.
C210921

Install the front No. 1 disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front No. 1 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 04947 7.INSTALL FRONT DISC BRAKE FITTING KIT

a.
C210935E04
2.042,4.25 2.042,4.354 false 1.573,4.25 1.573,4.344 false 1.563,0.875 1.563,0.979 false 2.052,0.885 2.052,0.979 false 1.479,4.354 1.646,4.51 0.167,0.156 10 false *1 1.958,0.99 2.125,1.156 0.167,0.167 10 false *1 1.938,4.354 2.104,4.51 0.167,0.156 10 false *2 1.469,0.99 1.635,1.156 0.167,0.167 10 false *2

Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.

Text in Illustration
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.



Hide 8.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C210919

Install the pad wear indicator plate to each front disc brake pad.

NOTICE:

Install each pad wear indicator plate in the correct position and direction.



b.
C263975E02
2.406,2.458 2.094,2.458 false 2.958,2.813 2.688,2.813 false 1.021,1.094 1.292,1.094 false 0.479,0.875 0.75,0.875 false 1.927,2.375 2.083,2.531 0.156,0.156 10 false *1 2.49,2.729 2.646,2.885 0.156,0.156 10 false *2 1.333,1 1.49,1.156 0.156,0.156 10 false *1 0.781,0.792 0.938,0.948 0.156,0.156 10 false *2

Install the front No. 1 anti-squeal shim and front No. 2 anti-squeal shim to each front disc brake pad.

Text in Illustration
*1 Front No. 1 Anti-squeal Shim
*2 Front No. 2 Anti-squeal Shim

NOTICE:

Install the shims in the correct positions and directions.



Hide 04465 9.INSTALL FRONT DISC BRAKE PAD

a.
C210917

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



Hide 10.INSTALL DISC BRAKE CYLINDER ASSEMBLY

a.
C236568E01
2.101,2.477 2.262,2.615 0.161,0.138 10 *b 2.87,2.73 3.035,2.880 0.165,0.150 10 *a

Hold the front disc brake cylinder slide pin, and install the disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Text in Illustration
*a Hold
*b Turn

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313J 11.CONNECT FRONT FLEXIBLE HOSE

a.
C210915

Connect the front flexible hose to the disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30 N*m (310 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 12.FILL RESERVOIR WITH BRAKE FLUID

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


b.

Perform the following procedure if air bleeding is not necessary:

i.

Connect the reservoir level switch connector.




Hide 15.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)