Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY › 2014.11–2016.05
RM2070E _54 Brake _061927 PARKING BRAKE _0301708 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEEL

Hide 4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42491 5.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 6.REMOVE REAR DISC

Hide 46550A 7.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)

a.
C233632

Remove the parking brake shoe return tension spring.


Hide 46550G 8.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)

a.
C233633

Remove the parking brake shoe return tension spring.


Hide 46555 9.REMOVE BRAKE SHOE HOLD DOWN SPRING (for Front Side)

a.
C236242E02
2.052,1.552 2.052,1.052 2.052,1.052 2.635,1.052 true 2.677,0.969 2.99,1.156 0.313,0.188 10 false SST

Using SST, remove the brake shoe hold down spring as shown in the illustration.

SST
09718-00011  


Hide 47614 10.REMOVE PARKING BRAKE SHOE STRUT

a.
C236243

Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.


b.
C236244

Remove the parking brake shoe strut.


Hide 46555 11.REMOVE BRAKE SHOE HOLD DOWN SPRING (for Rear Side)

a.
C236245E02
0.927,1.458 0.927,1.708 false 0.792,1.719 1.104,1.885 0.313,0.167 10 false SST

Using SST, remove the brake shoe hold down spring as shown in the illustration.

SST
09718-00011  


Hide 47406A 12.REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C236246

Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.


b.
C236247

Remove the parking brake shoe adjusting screw set.


Hide 46580 13.REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.
C236248

Remove the No. 1 parking brake shoe assembly.


Hide 46550E 14.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.
C236249

Remove the parking brake shoe return tension spring.


Hide 47612 15.SEPARATE PARKING BRAKE SHOE LEVER

a.
C236250

Using needle-nose pliers, separate the parking brake shoe lever from the No. 3 parking brake cable assembly as shown in the illustration.


Hide 47612 16.REMOVE PARKING BRAKE SHOE LEVER

a.
C236251

Using a screwdriver, remove the parking brake shoe type C washer, parking brake shoe shim and the parking brake shoe lever.

HINT:

Parking brake shoe shims are provided when necessary to adjust the clearance between the parking brake shoe lever and parking brake shoe type C washer. Some vehicles may not be equipped with shims.



Hide 47447C 17.REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Front Side)

a.
C236252

Remove the parking brake shoe hold down spring pin.


Hide 47447C 18.REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Rear Side)

a.

Remove the rear axle hub and bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL).


b.
C236253

Remove the nut to separate the parking plate sub-assembly from the rear axle beam assembly.

NOTICE:

Hang the parking plate sub-assembly using a wire or an equivalent tool.



c.
C236254

Remove the parking brake shoe hold down spring pin.