Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM2070E _54 Brake _061927 PARKING BRAKE _0301708 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 47447C 1.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Rear Side)

a.

Clean the installation surface of the parking plate sub-assembly.


b.

Install the parking brake shoe hold down spring pin.


c.

Temporarily install the parking plate sub-assembly to the rear axle hub and bearing assembly with the nut.

NOTICE:

Make sure that the No. 3 parking brake cable assembly is not twisted during reassembly.


HINT:

The parking plate sub-assembly will be fully installed after installing the rear axle hub and bearing assembly.



d.

Install the rear axle hub and bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION).


e.

Fully tighten the installation nut of the parking plate sub-assembly.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 47447C 2.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Front Side)

a.

Install the parking brake shoe hold down spring pin.


Hide 3.APPLY HIGH TEMPERATURE GREASE

a.
C236255

Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.

Text in Illustration
V100155

High Temperature Grease


Hide 47612 4.INSTALL PARKING BRAKE SHOE LEVER

a.
C236291

Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

Text in Illustration
V100155

High Temperature Grease


b.

Temporarily install the parking brake shoe lever to the No. 2 parking brake shoe assembly with a new parking brake shoe type C washer.


c.
C064143

Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

Standard clearance:

Less than 0.35 mm (0.0137 in.)


If the clearance is not as specified, replace the parking brake shoe shim with one of the correct size.

Part No. Shim Thickness
90564-09184 0.3 mm (0.0118 in.)
90564-09185 0.6 mm (0.0236 in.)
90564-09186 0.9 mm (0.0354 in.)


d.

Select a parking brake shoe shim and install it and the parking brake shoe type C washer.


e.
C064144

Using a pair of pliers, squeeze together the ends of the parking brake shoe type C washer.


f.

Check that the parking brake shoe lever moves smoothly.


Hide 47612 5.CONNECT PARKING BRAKE SHOE LEVER

a.
C236275

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever.


Hide 46550E 6.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.

Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.


Hide 46580 7.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.

Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.


Hide 47406A 8.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C236276

Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

Text in Illustration
V100155

High Temperature Grease


b.

Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.


c.
C236277

Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.

NOTICE:

Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.



Hide 46555 9.INSTALL BRAKE SHOE HOLD DOWN SPRING (for Rear Side)

a.
C236245E02
0.927,1.458 0.927,1.708 false 0.792,1.719 1.104,1.885 0.313,0.167 10 false SST

Using SST, install the brake shoe hold down spring as shown in the illustration.

SST
09718-00011  


Hide 47614 10.INSTALL PARKING BRAKE SHOE STRUT

a.

Install the parking brake shoe strut.


b.
C236278

Install the No. 1 parking brake shoe assembly.


Hide 46555 11.INSTALL BRAKE SHOE HOLD DOWN SPRING (for Front Side)

a.
C236242E02
2.052,1.552 2.052,1.052 2.052,1.052 2.635,1.052 true 2.677,0.969 2.99,1.156 0.313,0.188 10 false SST

Using SST, install the brake shoe hold down spring as shown in the illustration.

SST
09718-00011  


Hide 46550G 12.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)

a.

Install the parking brake shoe return tension spring.


Hide 46550A 13.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)

a.

Install the parking brake shoe return tension spring.


Hide 14. CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

U154841E01
3.754,0.118 3.989,0.331 0.236,0.212 10 *B 0.125,0.118 0.361,0.331 0.236,0.212 10 *A

Text in Illustration
*A LH Side *B RH Side
V100135

Front of the Vehicle - -

NOTICE:

There should be no oil or grease on the friction surfaces of the shoe linings or discs.



Hide 42431 15.INSTALL REAR DISC

Hide 42491 16.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 17.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 18.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL

Hide 19.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 20.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


b.

Connect the reservoir level switch connector.



Hide 21. BED IN PARKING BRAKE SHOES TO DISCS

a.

Drive the vehicle at about 50 km/h (31 mph) on a safe, level and dry road.


b.

Depress the parking brake pedal with 150 N (15 kgf, 33.7 lbf) of force.


c.

Drive the vehicle for about 400 m (0.25 mile) in this condition.


d.

Repeat this procedure 3 times.

NOTICE:

Set a 5-minute interval between each procedure to prevent the brake assembly from overheating.