Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2012.03–2013.08
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the EPS warning light comes on. At this time, the power steering ECU assembly stores a DTC in its memory.

WIRING DIAGRAM

C237994E22
0.99,0.542 1.396,0.698 0.406,0.156 10 false CANH 1.49,0.406 1.667,0.563 0.177,0.156 10 false 19 1.01,1.333 1.396,1.49 0.385,0.156 10 false CANL 5.938,0.542 6.344,0.698 0.406,0.156 10 false CANH 5.563,0.542 5.844,0.771 0.281,0.229 10 false L54 5.625,0.354 5.719,0.51 0.094,0.156 10 false 1 5.563,1.333 5.958,1.604 0.396,0.271 10 false L54 5.635,1.146 5.729,1.302 0.094,0.156 10 false 7 5.927,1.333 6.313,1.49 0.385,0.156 10 false CANL 5.563,2.313 5.958,2.708 0.396,0.396 10 false L54 5.635,2.125 5.729,2.281 0.094,0.156 10 false 6 5.938,2.323 6.104,2.479 0.167,0.156 10 false IG 5.563,3.125 6.042,3.51 0.479,0.385 10 false A27 5.625,2.927 5.76,3.135 0.135,0.208 10 false 2 5.927,3.135 6.354,3.292 0.427,0.156 10 false PGND 1.49,1.198 1.667,1.354 0.177,0.156 10 false 20 0.094,1.813 0.813,2.115 0.719,0.302 10 false L27 0.083,1.979 2.615,2.333 2.531,0.354 10 false Combination Meter Sub-assembly 0.167,2.313 1.708,2.583 1.542,0.271 10 false from IG1 No. 1 Relay 1.135,4.115 3.094,4.438 1.958,0.323 10 false : CAN Communication Line 3.302,2.479 4.792,2.885 1.49,0.406 10 false ECU-IG No. 2 5.125,4.042 7.125,4.365 2,0.323 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

OK

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
C351639E01
0.5,1.333 0.917,1.583 0.417,0.25 0.667,3.417 1.083,3.667 0.417,0.25 2.104,1.656 2.531,1.656 false 1.781,4.052 2.208,4.052 false 2.594,1.552 3.104,1.792 0.51,0.24 10 false IG 2.271,3.969 2.781,4.208 0.51,0.24 10 false PGND 0.75,3.458 1.26,3.698 0.51,0.24 10 false A27 0.594,1.365 1.104,1.604 0.51,0.24 10 false L54 0.146,0.146 0.656,0.385 0.51,0.24 10 false *a

Disconnect the connectors from the power steering ECU assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L54-6 (IG) - Body ground Power switch on (IG) 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

3.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER SUB-ASSEMBLY
a.

Reconnect the power steering ECU assembly connector.


b.

Perform the Active Test of the combination meter sub-assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter sub-assembly.

OK:

The EPS warning light turns on or off in accordance with the GTS operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE COMBINATION METER SUB-ASSEMBLY