Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2014.11–2016.05
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

C264870E01
1.263,1.186 1.438,1.346 0.174,0.161 10 13 0.964,1.284 1.166,1.444 0.202,0.161 10 TC 2.925,1.298 3.100,1.458 0.176,0.161 10 L5 2.925,1.083 3.101,1.243 0.176,0.161 10 11 4.193,0.69 4.367,0.851 0.174,0.161 10 L6 4.193,0.475 4.370,0.635 0.176,0.161 10 24 3.633,0.704 4.022,0.865 0.390,0.161 10 CA1L 4.193,2.082 4.372,2.242 0.178,0.161 10 L6 4.193,1.881 4.379,2.041 0.185,0.161 10 25 3.61,2.096 4.022,2.256 0.412,0.161 10 CA1H 5.971,0.704 6.360,0.865 0.390,0.161 10 CANL 5.78,0.55 5.875,0.711 0.095,0.161 10 7 5.78,1.942 5.875,2.102 0.095,0.161 10 1 5.971,2.096 6.383,2.256 0.412,0.161 10 CANH 1.263,1.92 1.438,2.081 0.174,0.161 10 4 0.938,2.018 1.166,2.179 0.228,0.161 10 CG 0.422,2.739 0.676,2.899 0.254,0.161 10 L61 0.744,2.739 1.119,2.899 0.375,0.161 10 DLC3 3.015,2.77 4.283,3.100 1.269,0.330 10 Power Management Control ECU 5.831,2.784 6.798,3.114 0.968,0.330 10 Power Steering ECU Assembly 5.51,2.796 5.762,2.977 0.252,0.181 10 L54 3.304,1.281 3.512,1.442 0.209,0.161 10 TC

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - L5-11 (TC) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U191005E02
1.677,1.958 2.406,1.01 true 0.271,0.25 0.458,0.417 0.188,0.167 10 false *a 2.365,0.813 2.604,0.979 0.24,0.167 10 false CG 0.281,1.042 0.531,1.188 0.25,0.146 10 false L61

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
U191006E02
1.854,2.396 2.583,0.958 true 0.271,0.25 0.458,0.417 0.188,0.167 10 false *a 2.531,0.802 2.771,0.969 0.24,0.167 10 false TC 0.292,1.042 0.542,1.188 0.25,0.146 10 false L61

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of DLC3

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU