Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2012.03–2013.08
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551/25  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the power switch status as on (IG) or off through the IG power source circuit.

DTC No. DTC Detection Condition Trouble Area
C1551/25 IG power source circuit malfunction inside ECU
·

ECU-IG No. 2 fuse

·

IG power source circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C113532E43
0.406,1.047 1.738,1.194 1.332,0.147 10 from IG1 No. 1 Relay 2.758,1.204 3.640,1.341 0.883,0.137 10 ECU-IG No. 2 4.455,1.052 4.744,1.194 0.289,0.142 10 L54 4.843,1.052 5.010,1.194 0.167,0.142 10 IG 4.535,0.87 4.630,1.012 0.096,0.142 10 6 4.46,2.159 4.730,2.301 0.270,0.142 10 A27 4.843,2.159 5.267,2.301 0.424,0.142 10 PGND 4.539,1.977 4.635,2.119 0.096,0.142 10 2 4.599,2.915 6.731,3.054 2.132,0.139 10 Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG power supply" in the Data List and read the value displayed on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG power supply IG power supply/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)

OK:

The normal condition value is displayed on the GTS.




OK

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER STEERING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER STEERING ECU ASSEMBLY)
a.
C351639E01
0.5,1.333 0.917,1.583 0.417,0.25 0.667,3.417 1.083,3.667 0.417,0.25 2.104,1.656 2.531,1.656 false 1.781,4.052 2.208,4.052 false 2.594,1.552 3.104,1.792 0.51,0.24 10 false IG 2.271,3.969 2.781,4.208 0.51,0.24 10 false PGND 0.75,3.458 1.26,3.698 0.51,0.24 10 false A27 0.594,1.365 1.104,1.604 0.51,0.24 10 false L54 0.146,0.146 0.656,0.385 0.51,0.24 10 false *a

Disconnect the connectors from the power steering ECU assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L54-6 (IG) - Body ground Power switch on (IG) 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR