Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2016.05
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/22  PIG Power Supply Voltage Malfunction  C1554/23  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist.

DTC No. DTC Detection Condition Trouble Area
C1552/22 PIG power source circuit malfunction inside ECU
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


C1554/23 Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C246150E01
4.604,0.706 4.930,0.886 0.326,0.180 10 PIG 4.464,2.975 4.790,3.156 0.326,0.180 10 A27 4.394,0.601 4.539,0.781 0.145,0.180 10 1 4.394,2.065 4.548,2.245 0.154,0.180 10 2 4.604,2.156 5.055,2.336 0.451,0.180 10 PGND 2.601,0.895 2.927,1.075 0.326,0.180 10 EPS 1.186,1.273 1.598,1.453 0.413,0.180 10 MAIN 1.298,2.331 2.377,2.511 1.080,0.180 10 Auxiliary Battery 4.464,3.165 6.436,3.345 1.972,0.180 10 Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (READY).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PIG Power Supply PIG power supply/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always

OK:

The normal condition value is displayed on the GTS.




OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
U154680E01
0.255,0.214 0.462,0.413 0.207,0.200 10 *a 0.797,2.235 1.071,2.374 0.274,0.139 10 A27 2.219,2.186 2.481,2.330 0.262,0.144 10 PIG 2.219,2.554 2.641,2.694 0.422,0.140 10 PGND 1.893,2.276 2.174,2.276 false 1.893,2.637 2.174,2.637 false

Disconnect the connector from the power steering ECU assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-1 (PIG) - Body ground Always 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR