Power is supplied to the radio and display receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the illumination for the radio and display receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except radio and display receiver assembly. | B |
| No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). | C |
A
B
C
Disconnect the L52 spiral cable with sensor sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L52-12 (IL+2) - Body ground | Power switch off
Light control switch in the tail or head position |
11 to 14 V |
OK
NG
Remove the steering pad switch (w/o TFT Display) (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).
Remove the steering pad switch (w/ TFT Display) (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).
Connect a positive (+) lead from the auxiliary battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.
| *a | Component without harness connected
(Steering Pad Switch) |
- | - |
Check if the illumination for the steering pad switch comes on.
Illumination for the steering pad switch comes on.
Proceed to the next step based on the inspection result.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the steering pad switch RH connectors (w/o TFT Display).
Disconnect the steering pad switch RH connectors (w/ TFT Display).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SR2-2 (IL+2) - z9-5 (IL+2) | Always | Below 2.5 Ω |
| SR2-1 (EAU) - z9-8 (EAU) | Always | Below 2.5 Ω |
| *a | Component without harness connected
(Steering Pad Switch RH) |
- | - |
OK
NG
Remove the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-5 (IL+2) - L52-12 (IL+2) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z9-8 (EAU) - L52-4 (EAU) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-5 (IL+2) - L52-12 (IL+2) | Always | 3 Ω or less |
| z9-8 (EAU) - L52-4 (EAU) | Always | 3 Ω or less |
Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.
The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.
As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.
| *a | Component without harness connected
(Spiral Cable with Sensor Sub-assembly) |
| *b | Steering Pad Switch Side |
| *c | Vehicle Side |
OK
NG
Disconnect the L52 spiral cable with sensor sub-assembly connector.
Disconnect the L35 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L52-4 (EAU) - L35-23 (SWG) | Always | Below 1 Ω |
OK
NG
Disconnect the L167 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L167-10 (ILL+) - Body ground | Power switch off
Light control switch in the tail or head position |
11 to 14 V |
OK
NG
Disconnect the L166 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L166-5 (ILL-) - Body ground | Always | Below 1 Ω |
OK
NG