Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2016.05–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E311632E02
2.052,1.281 2.146,1.427 0.094,0.146 10 false 2 2.052,1.833 2.146,1.979 0.094,0.146 10 false 1 2.208,1.375 2.5,1.521 0.292,0.146 10 false IL+2 2.208,1.938 2.521,2.083 0.313,0.146 10 false EAU 2.042,2.354 2.354,2.5 0.313,0.146 10 false SR2 0.094,2.354 1.594,2.5 1.5,0.146 10 false Steering Pad Switch LH 2.042,2.5 2.865,2.823 0.823,0.323 10 false Steering Pad Switch RH 3.25,1.188 3.344,1.333 0.094,0.146 10 false 5 3.229,1.385 3.417,1.531 0.188,0.146 10 false z9 4.146,1.188 4.323,1.333 0.177,0.146 10 false 12 4.115,1.385 4.406,1.531 0.292,0.146 10 false L52 3.615,1.281 3.906,1.427 0.292,0.146 10 false IL+2 3.25,1.74 3.344,1.885 0.094,0.146 10 false 8 3.24,1.938 3.427,2.083 0.188,0.146 10 false z9 4.198,1.76 4.375,1.906 0.177,0.146 10 false 4 4.125,1.948 4.417,2.094 0.292,0.146 10 false L52 3.635,1.844 3.948,1.99 0.313,0.146 10 false EAU 3.229,2.365 4.615,2.771 1.385,0.406 10 false Spiral Cable with Sensor Sub-assembly 2.552,0.344 3.729,0.698 1.177,0.354 10 false from TAIL Relay 4.448,0.917 4.76,1.063 0.313,0.146 10 false TAIL 4.375,0.49 4.854,0.635 0.479,0.146 10 false PANEL 5.885,3.833 7.115,4.219 1.229,0.385 10 false Radio and Display Receiver Assembly 6.292,3.354 6.552,3.5 0.26,0.146 10 false ILL- 6,3.146 6.094,3.292 0.094,0.146 10 false 5 5.896,3.344 6.292,3.49 0.396,0.146 10 false L166 6.313,1.385 6.604,1.531 0.292,0.146 10 false ILL+ 5.938,1.188 6.115,1.333 0.177,0.146 10 false 10 5.875,1.385 6.313,1.531 0.438,0.146 10 false L167 6.292,1.958 6.688,2.104 0.396,0.146 10 false SWG 5.958,1.75 6.135,1.896 0.177,0.146 10 false 23 5.917,1.938 6.25,2.083 0.333,0.146 10 false L35

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the L52 spiral cable with sensor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-12 (IL+2) - Body ground Power switch off
Light control switch in the tail or head position
11 to 14 V




OK

3.INSPECT STEERING PAD SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH
a.

Remove the steering pad switch (w/o TFT Display) (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

U155195E01
4.221,2.113 3.821,2.513 false 3.624,2.633 3.224,3.033 false 2.938,2.464 3.112,2.627 0.174,0.163 10 z9 4.246,2.043 4.563,2.204 0.317,0.161 10 IL+2 3.07,3.044 3.388,3.205 0.317,0.161 10 EAU 0.134,0.078 0.451,0.239 0.317,0.161 10 *a


b.

Remove the steering pad switch (w/ TFT Display) (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

U155199E02
3.271,3.167 3.573,2.635 false 3.781,2.51 4.083,1.979 false 0.156,0.073 0.646,0.292 0.49,0.219 10 false *a 2.917,2.427 3.406,2.646 0.49,0.219 10 false z9 4.125,1.906 4.615,2.125 0.49,0.219 10 false IL+2 3.125,3.177 3.615,3.396 0.49,0.219 10 false EAU


c.

Connect a positive (+) lead from the auxiliary battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.

Text in Illustration
*a Component without harness connected
(Steering Pad Switch)
- -


d.

Check if the illumination for the steering pad switch comes on.

OK:

Illumination for the steering pad switch comes on.



e.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

4.INSPECT STEERING PAD SWITCH RH

B

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
4.INSPECT STEERING PAD SWITCH RH
a.

Disconnect the steering pad switch RH connectors (w/o TFT Display).

U155200E02
3.781,2.479 4.313,2.104 false 2.76,3.156 3.573,2.656 false 1.208,1.927 1.594,1.396 false 1.802,1.958 1.729,1.396 false 0.104,0 0.771,0.281 0.667,0.281 10 false *a 0.958,1.25 1.625,1.531 0.667,0.281 10 false SR2 2.813,2.438 3.208,2.677 0.396,0.24 10 false z9 2.615,3.177 3.281,3.458 0.667,0.281 10 false EAU 4.188,1.938 4.854,2.219 0.667,0.281 10 false IL+2 1.052,1.927 1.719,2.208 0.667,0.281 10 false EAU 1.688,1.99 2.354,2.271 0.667,0.281 10 false IL+2


b.

Disconnect the steering pad switch RH connectors (w/ TFT Display).

U155148E02
1.698,1.438 1.448,1.688 false 1.833,1.438 1.833,1.688 false 4.156,2.24 3.885,2.552 false 3.677,2.719 3.396,3 false 0.135,0.115 0.615,0.281 0.479,0.167 10 false *a 1.073,1.333 1.427,1.5 0.354,0.167 10 false SR2 4.188,2.115 4.542,2.281 0.354,0.167 10 false IL+2 1.208,1.708 1.563,1.875 0.354,0.167 10 false EAU 3.198,3.021 3.552,3.188 0.354,0.167 10 false EAU 1.688,1.698 2.042,1.865 0.354,0.167 10 false IL+2 2.938,2.531 3.292,2.698 0.354,0.167 10 false z9


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SR2-2 (IL+2) - z9-5 (IL+2) Always Below 2.5 Ω
SR2-1 (EAU) - z9-8 (EAU) Always Below 2.5 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -



OK

REPLACE STEERING PAD SWITCH LH

NG

REPLACE STEERING PAD SWITCH RH

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

E343950E02
3.417,3.5 3.833,3.75 0.417,0.25 3.583,0.333 4,0.583 0.417,0.25 3.698,4.375 3.698,4.115 false 4.083,3.979 3.927,3.979 false 3.594,0.927 3.438,0.927 false 3.865,1.24 3.865,1.083 false 2.073,0.219 2.385,0.417 0.313,0.198 10 false *a 3.031,0.271 3.344,0.469 0.313,0.198 10 false *b 3.719,0.375 4.031,0.573 0.313,0.198 10 false z9 2.813,3.427 3.125,3.625 0.313,0.198 10 false *c 3.51,3.552 3.969,3.75 0.458,0.198 10 false L52 3.083,0.844 3.448,1.042 0.365,0.198 10 false IL+2 3.708,1.25 4.073,1.448 0.365,0.198 10 false EAU 3.552,4.396 3.917,4.594 0.365,0.198 10 false EAU 4.104,3.885 4.469,4.083 0.365,0.198 10 false IL+2

Standard Resistance:
Tester Connection Condition Specified Condition
z9-5 (IL+2) - L52-12 (IL+2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z9-8 (EAU) - L52-4 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-5 (IL+2) - L52-12 (IL+2) Always 3 Ω or less
z9-8 (EAU) - L52-4 (EAU) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.



Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Side
*c Vehicle Side



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the L52 spiral cable with sensor sub-assembly connector.


b.

Disconnect the L35 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-4 (EAU) - L35-23 (SWG) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the L167 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L167-10 (ILL+) - Body ground Power switch off
Light control switch in the tail or head position
11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the L166 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L166-5 (ILL-) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR