Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in the AVC-LAN, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

E277861E20
0.975,1.809 2.353,1.983 1.378,0.174 10 Parking Assist ECU 4.74,1.678 5.194,1.825 0.455,0.147 10 L169 4.74,1.867 6.525,2.206 1.786,0.339 10 Radio and Display Receiver Assembly 5.122,1.157 5.501,1.304 0.378,0.147 10 TX3- 5.122,0.344 5.542,0.519 0.420,0.174 10 TX3+ 4.903,1.064 5.014,1.210 0.111,0.147 10 8 4.903,0.251 5.008,0.425 0.105,0.174 10 7 1.819,1.176 2.065,1.322 0.246,0.147 10 TX- 1.784,0.363 2.064,0.537 0.280,0.174 10 TX+ 2.199,1.059 2.434,1.206 0.235,0.147 10 10 2.18,0.246 2.378,0.421 0.198,0.174 10 11 0.786,1.643 1.137,1.790 0.350,0.147 10 L64 0.936,2.395 3.349,2.569 2.413,0.174 10 : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the radio and display receiver assembly connector.


b.
E286972E04
0.155,0.155 0.467,0.496 0.312,0.341 10 *a 1.018,1.079 1.488,1.244 0.470,0.165 10 TX3- 1.804,1.079 2.274,1.278 0.470,0.200 10 TX3+ 1.527,1.747 1.234,1.281 false 1.639,1.756 1.977,1.282 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L169-7 (TX3+) - L169-8 (TX3-) Always 60 to 80 Ω


Text in Illustration
*a Component without harness connected
(Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the radio and display receiver assembly connector.


b.

Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-11 (TX+) - L169-7 (TX3+) Always Below 1 Ω
L64-10 (TX-) - L169-8 (TX3-) Always Below 1 Ω
L64-11 (TX+) - Body ground Always 10 kΩ or higher
L64-10 (TX-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.




OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY