Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch, also the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E310188E04
4.74,0.698 4.979,0.896 0.24,0.198 10 false z9 5.552,0.688 5.938,0.885 0.385,0.198 10 false L52 4.719,0.5 4.948,0.688 0.229,0.188 10 false 10 4.75,1.604 4.958,1.792 0.208,0.188 10 false 8 4.76,2.719 4.969,2.906 0.208,0.188 10 false 9 5.615,0.49 5.875,0.688 0.26,0.198 10 false 6 5.615,1.594 5.781,1.792 0.167,0.198 10 false 4 5.656,2.667 5.823,2.865 0.167,0.198 10 false 5 3.667,1.688 3.833,1.875 0.167,0.188 10 false 1 3.667,0.583 3.833,0.771 0.167,0.188 10 false 4 5.115,0.594 5.5,0.792 0.385,0.198 10 false AU1 3.896,0.677 4.281,0.875 0.385,0.198 10 false AU1 5.094,1.708 5.479,1.906 0.385,0.198 10 false EAU 3.875,1.813 4.26,2.01 0.385,0.198 10 false EAU 5.115,2.802 5.5,3 0.385,0.198 10 false AU2 3.885,2.885 4.271,3.083 0.385,0.198 10 false AU2 6.427,0.698 6.875,0.865 0.448,0.167 10 false SW1 6.417,1.813 6.844,1.979 0.427,0.167 10 false SWG 0.177,1.135 0.781,1.344 0.604,0.208 10 false Volume- 6.271,3.448 7.031,4.115 0.76,0.667 10 false Radio and Display Receiver Assembly 4.75,3.365 5.646,3.99 0.896,0.625 10 false Spiral Cable with Sensor Sub-assembly 3.688,3.531 4.521,3.906 0.833,0.375 10 false Steering Pad Switch RH 0.896,1.135 1.542,1.344 0.646,0.208 10 false Volume+ 1.74,1.135 2.125,1.344 0.385,0.208 10 false Seek- 2.406,1.135 2.896,1.344 0.49,0.208 10 false Seek+ 4.729,1.802 4.969,2 0.24,0.198 10 false z9 4.74,2.917 4.979,3.115 0.24,0.198 10 false z9 5.542,1.802 5.927,2 0.385,0.198 10 false L52 5.542,2.917 5.927,3.115 0.385,0.198 10 false L52 6.188,0.604 6.365,0.802 0.177,0.198 10 false 21 6.188,1.698 6.365,1.896 0.177,0.198 10 false 23 6.188,2.823 6.365,3.021 0.177,0.198 10 false 22 6.427,2.938 6.875,3.104 0.448,0.167 10 false SW2 6.104,3.26 6.417,3.458 0.313,0.198 10 false L35 3.688,3.354 4,3.552 0.313,0.198 10 false SR2 2.323,2.292 2.844,2.5 0.521,0.208 10 false MODE 0.99,3.688 1.635,3.896 0.646,0.208 10 false On hook 1.781,3.688 2.417,3.896 0.635,0.208 10 false Off hook 2.729,3.688 3.135,3.896 0.406,0.208 10 false Voice 0.896,4.802 2.844,5.021 1.948,0.219 10 false Steering Pad Switch LH 3.656,2.813 3.823,3.01 0.167,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-21 (SW1) - L35-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
L35-22 (SW2) - L35-23 (SWG) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH
2.INSPECT STEERING PAD SWITCH
a.

Remove the steering pad switch (w/o TFT Display) (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

U155194E02
3.698,2.677 3.698,3.021 false 4.042,3.021 3.802,2.677 false 3.354,3.021 3.583,2.677 false 1.656,1.24 2.177,0.729 false 1.677,1.542 2.208,1.813 false 1.396,1.542 1.052,1.802 false 1.417,1.26 1.094,0.885 false 1.438,1.354 0.906,1.208 false 1.771,2.24 1.344,2.656 false 1.896,2.479 1.438,2.948 false 1.688,1.938 1.26,2.365 false 2.927,2.458 3.188,2.688 0.26,0.229 10 false z9 3.542,3.031 3.865,3.219 0.323,0.188 10 false AU2 3.938,3.031 4.26,3.219 0.323,0.188 10 false AU1 3.135,3.031 3.458,3.219 0.323,0.188 10 false EAU 0.135,0.052 0.292,0.24 0.156,0.188 10 false *a 2.198,0.615 2.354,0.802 0.156,0.188 10 false *b 0.948,0.75 1.104,0.938 0.156,0.188 10 false *d 0.771,1.135 0.927,1.323 0.156,0.188 10 false *f 0.896,1.75 1.052,1.938 0.156,0.188 10 false *e 2.219,1.771 2.375,1.958 0.156,0.188 10 false *c 1.271,2.896 1.427,3.083 0.156,0.188 10 false *h 1.177,2.594 1.333,2.781 0.156,0.188 10 false *g 1.104,2.302 1.26,2.49 0.156,0.188 10 false *i


b.

Remove the steering pad switch (w/ TFT Display) (see page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

U155197E02
0.698,0.604 1.375,1.229 1.375,1.229 1.396,1.229 false 0.573,1.25 1.542,1.323 false 0.646,1.646 1.385,1.51 false 1.635,1.208 2.333,0.604 false 1.708,1.5 2.25,1.76 false 1.083,2.281 1.667,1.979 false 1.177,2.594 1.719,2.229 false 1.323,2.875 1.844,2.448 false 2.99,2.99 3.583,2.656 false 3.792,2.667 4.219,3.042 false 3.594,3 3.688,2.667 false 2.365,0.458 3.104,0.75 0.74,0.292 10 false *b 2.833,3.042 3.479,3.24 0.646,0.198 10 false EAU 3.49,3.031 3.896,3.25 0.406,0.219 10 false AU2 4.115,3.063 4.531,3.281 0.417,0.219 10 false AU1 2.792,2.427 3.208,2.646 0.417,0.219 10 false z9 0.094,0 0.51,0.219 0.417,0.219 10 false *a 0.5,0.521 0.917,0.74 0.417,0.219 10 false *d 0.406,1.146 0.823,1.365 0.417,0.219 10 false *f 0.479,1.594 0.896,1.813 0.417,0.219 10 false *e 0.875,2.188 1.292,2.406 0.417,0.219 10 false *i 0.99,2.51 1.406,2.729 0.417,0.219 10 false *g 1.156,2.802 1.573,3.021 0.417,0.219 10 false *h 2.302,1.688 2.719,1.906 0.417,0.219 10 false *c


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-10 (AU1) - z9-8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
z9-9 (AU2) - z9-8 (EAU) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch)
*b Seek+
*c Seek- *d Volume+
*e Volume- *f MODE
*g On hook *h Off hook
*i Voice - -


d.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

3.INSPECT STEERING PAD SWITCH RH

B

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
3.INSPECT STEERING PAD SWITCH RH
a.

Disconnect the steering pad switch RH connectors (w/o TFT Display).

U155147E01
0.154,0.131 0.409,0.360 0.255,0.229 10 *a 2.87,2.56 3.125,2.790 0.255,0.229 10 z9 3.155,2.993 3.464,3.139 0.310,0.146 10 EAU 3.659,2.993 3.969,3.139 0.310,0.146 10 AU2 4.084,2.993 4.394,3.139 0.310,0.146 10 AU1 0.925,1.357 1.239,1.586 0.313,0.229 10 SR2 3.697,2.734 3.446,2.985 false 3.798,2.734 3.798,2.985 false 3.898,2.734 4.144,2.98 false 2.243,1.724 2.553,1.870 0.310,0.146 10 AU1 1.823,1.724 2.133,1.870 0.310,0.146 10 AU2 1.268,1.724 1.577,1.870 0.310,0.146 10 EAU 1.706,1.465 1.455,1.716 false 1.962,1.465 1.962,1.716 false 2.117,1.465 2.364,1.711 false


b.

Disconnect the steering pad switch RH connectors (w/ TFT Display).

U155198E02
1.604,1.365 1.094,1.729 false 1.865,1.385 1.667,1.813 false 2.208,1.75 2,1.396 false 3.583,2.646 3.125,3.042 false 3.635,3.01 3.677,2.646 false 4.167,3.042 3.792,2.646 false 0.938,1.271 1.333,1.521 0.396,0.25 10 false SR2 2.865,2.427 3.198,2.677 0.333,0.25 10 false z9 0.958,1.75 1.5,2 0.542,0.25 10 false EAU 1.531,1.844 2.073,2.094 0.542,0.25 10 false AU2 2.083,1.781 2.625,2.031 0.542,0.25 10 false AU1 2.948,3.063 3.49,3.313 0.542,0.25 10 false EAU 3.49,3.083 4.031,3.333 0.542,0.25 10 false AU2 4.042,3.073 4.583,3.323 0.542,0.25 10 false AU1 0.104,0.104 0.438,0.354 0.333,0.25 10 false *a


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SR2-4 (AU1) - z9-10 (AU1) Always Below 2.5 Ω
SR2-3 (AU2) - z9-9 (AU2) Always Below 2.5 Ω
SR2-1 (EAU) - z9-8 (EAU) Always Below 2.5 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -



OK

REPLACE STEERING PAD SWITCH LH

NG

REPLACE STEERING PAD SWITCH RH

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

E343950E01
3.417,3.5 3.833,3.75 0.417,0.25 3.583,0.333 4,0.583 0.417,0.25 3.458,1.25 3.625,1.083 false 3.365,4.365 3.667,4.115 false 3.74,1.24 3.771,1.073 false 3.865,4.375 3.802,4.115 false 4.188,4.344 3.927,4.115 false 4,1.229 3.875,1.073 false 1.656,0.313 1.969,0.51 0.313,0.198 10 false *a 3.031,0.271 3.344,0.469 0.313,0.198 10 false *b 3.719,0.375 4.031,0.573 0.313,0.198 10 false z9 2.813,3.427 3.125,3.625 0.313,0.198 10 false *c 3.51,3.552 3.969,3.75 0.458,0.198 10 false L52 3.292,1.25 3.656,1.448 0.365,0.198 10 false AU1 3.615,1.25 3.979,1.448 0.365,0.198 10 false AU2 3.938,1.26 4.302,1.458 0.365,0.198 10 false EAU 3.229,4.396 3.594,4.594 0.365,0.198 10 false EAU 3.719,4.406 4.083,4.604 0.365,0.198 10 false AU2 4.104,4.396 4.469,4.594 0.365,0.198 10 false AU1

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z9-10 (AU1) - L52-6 (AU1) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z9-9 (AU2) - L52-5 (AU2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Always 3 Ω or less
z9-10 (AU1) - L52-6 (AU1) Always 3 Ω or less
z9-9 (AU2) - L52-5 (AU2) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.



Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Side
*c Vehicle Side



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY