Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2013.08–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the meter circuit plate to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E309036E02
0.626,1.485 1.749,1.636 1.123,0.151 10 Skid Control ECU 1.429,0.488 1.720,0.639 0.292,0.151 10 SP1 0.626,1.339 0.945,1.520 0.319,0.181 10 A58 1.783,0.488 1.969,0.636 0.187,0.148 10 11 3.048,7.054 4.268,7.216 1.220,0.162 10 Junction Connector 0.275,2.829 2.595,3.205 2.320,0.376 10 Power Management Control ECU 0.275,2.677 0.565,2.841 0.290,0.164 10 L5 0.095,6.83 0.360,6.993 0.265,0.164 10 A48 0.095,6.992 2.407,7.172 2.312,0.180 10 Headlight Leveling ECU Assembly*4 1.334,6.56 1.747,6.715 0.413,0.154 10 SPDR 1.379,2.385 1.779,2.540 0.400,0.154 10 SPDI 1.783,2.385 1.962,2.544 0.180,0.159 10 14 1.785,6.56 1.968,6.719 0.183,0.159 10 16 3.912,2.385 4.348,2.547 0.436,0.162 10 31*2 3.912,2.231 4.348,2.393 0.436,0.162 10 32*1 2.863,2.385 3.082,2.547 0.219,0.162 10 22 1.805,3.874 2.008,4.035 0.203,0.162 10 24 5.307,6.56 5.524,6.722 0.217,0.162 10 11 3.912,3.87 4.295,4.031 0.383,0.162 10 12*2 3.937,3.716 4.320,3.877 0.383,0.162 10 3*1 2.722,3.87 3.104,4.031 0.383,0.162 10 21*2 2.722,3.716 3.104,3.877 0.383,0.162 10 12*1 3.912,6.562 4.295,6.724 0.383,0.162 10 11*2 3.918,6.396 4.301,6.558 0.383,0.162 10 21*1 2.722,6.562 3.104,6.724 0.383,0.162 10 32*2 2.722,6.396 3.104,6.558 0.383,0.162 10 31*1 5.294,0.488 5.598,0.638 0.304,0.150 10 16 5.294,2.385 5.569,2.535 0.275,0.150 10 15 5.542,0.586 5.741,0.736 0.198,0.150 10 SI 5.542,2.496 5.743,2.647 0.201,0.151 10 +S 4.964,2.755 5.296,2.900 0.332,0.145 10 L27 4.964,2.918 7.091,3.149 2.126,0.231 10 Combination Meter Sub-assembly 0.16,4.172 0.520,4.326 0.360,0.153 10 L146 0.154,4.335 2.598,4.604 2.444,0.269 10 Windshield Wiper Relay Assembly*3 4.948,5.666 7.147,5.961 2.200,0.295 10 Navigation ECU Sub-assembly*6 0.556,7.599 1.372,7.781 0.817,0.182 10 *1: for LHD 1.746,7.599 2.563,7.781 0.817,0.182 10 *2: for RHD 2.923,7.599 4.698,7.781 1.775,0.182 10 *3: w/ Auto Wiper System 4.996,7.599 6.336,7.781 1.340,0.182 10 *4: w/ LED Headlight 0.556,7.988 2.298,8.170 1.743,0.182 10 *5: w/o Navigation System 2.923,7.988 4.532,8.170 1.608,0.182 10 *6: w/ Navigation System 1.432,3.874 1.760,4.019 0.328,0.145 10 SPD 5.551,6.56 5.880,6.706 0.328,0.145 10 SPD 4.97,5.515 5.245,5.661 0.275,0.145 10 L38 4.503,6.852 4.778,7.005 0.275,0.153 10 L31 4.547,4.129 4.846,4.284 0.299,0.156 10 L35 4.503,7.012 7.135,7.189 2.632,0.177 10 Stereo Component Amplifier Assembly*7 4.547,4.288 7.078,4.463 2.531,0.176 10 Radio and Display Receiver Assembly*5 2.753,7.054 3.067,7.218 0.314,0.164 10 L70 5.547,3.876 5.860,4.037 0.313,0.162 10 SPD 5.309,3.876 5.483,4.037 0.174,0.162 10 17 5.547,5.221 5.860,5.383 0.313,0.162 10 SPD 5.309,5.221 5.483,5.383 0.174,0.162 10 17 4.996,7.988 6.706,8.170 1.710,0.182 10 *7: for 8 Speakers 2.789,5.233 3.172,5.394 0.383,0.162 10 3*2 2.789,5.067 3.172,5.228 0.383,0.162 10 1*1 1.809,5.223 2.012,5.384 0.203,0.162 10 2 0.164,5.533 0.524,5.686 0.360,0.153 10 R41 0.158,5.696 3.083,6.022 2.925,0.327 10 Tire Pressure Warning ECU and Receiver*8 1.436,5.223 1.765,5.368 0.328,0.145 10 SPD 0.556,8.376 2.949,8.557 2.393,0.182 10 *8: w/ Tire Pressure Warning System

PROCEDURE

1.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
a.
E362569E01
1.042,1.99 1.26,1.333 false 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.583,0.385 1.896,0.583 0.313,0.198 10 false L27 2.792,3.594 3.177,3.802 0.385,0.208 10 false GND 1.083,3.875 1.396,4.073 0.313,0.198 10 false (A) 0.906,2.021 1.219,2.219 0.313,0.198 10 false +S

Check the output waveform.

i.

Remove the meter circuit plate with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L27-15 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Meter Circuit Plate)




OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E361813E01
1.521,0.417 1.938,0.667 0.417,0.25 1.302,1.313 0.969,0.792 false 0.125,0.083 0.594,0.333 0.469,0.25 10 false *a 0.771,0.604 1.24,0.854 0.469,0.25 10 false SPD 1.604,0.448 2.073,0.698 0.469,0.25 10 false L31 6.031,1.719 6.5,1.969 0.469,0.25 10 false GND 4.646,1.969 5.115,2.219 0.469,0.25 10 false (A)

i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L31-11 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L31-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 4 JUNCTION BLOCK)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 4 JUNCTION BLOCK)
a.

Disconnect the L31 stereo component amplifier assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L31-11 (SPD) - L70-21 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L31-11 (SPD) - L70-11 Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)