Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Speaker Circuit  


DESCRIPTION

for 6 Speakers:

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.


for 8 Speakers:

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.


WIRING DIAGRAM

for 6 Speakers


E230315E15
5.667,7.49 6.854,8.083 1.188,0.594 10 false Radio and Display Receiver Assembly 3.021,1.271 4.302,1.927 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 5.542,0.75 5.646,0.906 0.104,0.156 10 false 1 4.531,0.854 4.635,1.01 0.104,0.156 10 false 2 4.531,1.708 4.635,1.865 0.104,0.156 10 false 4 2.323,0.854 2.427,1.01 0.104,0.156 10 false 1 2.333,1.719 2.438,1.875 0.104,0.156 10 false 3 2.469,0.844 2.573,1 0.104,0.156 10 false + 2.469,1.698 2.573,1.854 0.104,0.156 10 false - 4.375,0.854 4.479,1.01 0.104,0.156 10 false + 4.385,1.698 4.49,1.854 0.104,0.156 10 false - 5.469,0.948 5.719,1.104 0.25,0.156 10 false L36 3.021,1.115 3.281,1.271 0.26,0.156 10 false I2 0.344,1.292 1.625,1.948 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.344,1.115 0.604,1.271 0.26,0.156 10 false N1 3.021,3.219 4.302,3.875 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 4.531,2.823 4.635,2.979 0.104,0.156 10 false 2 4.531,3.688 4.635,3.844 0.104,0.156 10 false 4 2.323,2.802 2.427,2.958 0.104,0.156 10 false 1 2.333,3.688 2.438,3.844 0.104,0.156 10 false 3 2.479,2.813 2.583,2.969 0.104,0.156 10 false + 2.479,3.667 2.583,3.823 0.104,0.156 10 false - 4.375,2.813 4.479,2.969 0.104,0.156 10 false + 4.385,3.677 4.49,3.833 0.104,0.156 10 false - 3.021,3.073 3.281,3.229 0.26,0.156 10 false I3 0.344,3.25 1.625,3.906 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.344,3.073 0.604,3.229 0.26,0.156 10 false O1 0.74,5.031 1.646,5.688 0.906,0.656 10 false Rear Speaker Assembly RH 0.74,4.875 1,5.031 0.26,0.156 10 false P3 0.74,6.583 1.646,7.24 0.906,0.656 10 false Rear Speaker Assembly LH 0.74,6.417 1,6.573 0.26,0.156 10 false Q3 5.469,1.813 5.719,1.969 0.25,0.156 10 false L36 5.469,2.917 5.719,3.073 0.25,0.156 10 false L36 5.479,3.792 5.729,3.948 0.25,0.156 10 false L36 5.469,4.833 5.719,4.99 0.25,0.156 10 false L41 5.469,5.469 5.719,5.625 0.25,0.156 10 false L41 5.469,6.354 5.719,6.51 0.25,0.156 10 false L41 5.469,6.99 5.719,7.146 0.25,0.156 10 false L41 5.844,0.958 6.135,1.115 0.292,0.156 10 false FR+ 5.844,1.823 6.104,1.979 0.26,0.156 10 false FR- 5.844,2.917 6.104,3.073 0.26,0.156 10 false FL+ 5.844,3.792 6.104,3.948 0.26,0.156 10 false FL- 5.844,4.844 6.146,5 0.302,0.156 10 false RR+ 5.844,5.479 6.125,5.635 0.281,0.156 10 false RR- 5.844,6.365 6.125,6.521 0.281,0.156 10 false RL+ 5.844,6.99 6.104,7.146 0.26,0.156 10 false RL- 5.531,6.781 5.635,6.938 0.104,0.156 10 false 6 5.542,6.156 5.646,6.313 0.104,0.156 10 false 2 5.542,5.271 5.646,5.427 0.104,0.156 10 false 3 5.531,4.615 5.635,4.771 0.104,0.156 10 false 1 5.552,3.594 5.656,3.75 0.104,0.156 10 false 6 5.531,2.708 5.635,2.865 0.104,0.156 10 false 2 5.542,1.604 5.646,1.76 0.104,0.156 10 false 5 1.792,1.052 1.896,1.208 0.104,0.156 10 false 1 1.792,1.708 1.896,1.865 0.104,0.156 10 false 2 1.792,3.031 1.896,3.188 0.104,0.156 10 false 1 1.792,3.688 1.896,3.844 0.104,0.156 10 false 2 1.792,4.844 1.896,5 0.104,0.156 10 false 1 1.792,5.479 1.896,5.635 0.104,0.156 10 false 2 1.792,6.354 1.896,6.51 0.104,0.156 10 false 1 1.792,7 1.896,7.156 0.104,0.156 10 false 2


for 8 Speakers


E250487E03
5.792,2.844 5.885,3 0.094,0.156 10 false 9 5.979,2.948 6.271,3.104 0.292,0.156 10 false FR+ 5.979,3.604 6.24,3.76 0.26,0.156 10 false FR- 5.979,4.063 6.24,4.219 0.26,0.156 10 false FL+ 5.979,4.698 6.24,4.854 0.26,0.156 10 false FL- 5.979,0.719 6.406,0.875 0.427,0.156 10 false WFR+ 5.979,1.354 6.375,1.51 0.396,0.156 10 false WFR- 5.979,1.844 6.385,2 0.406,0.156 10 false WFL+ 5.979,2.469 6.354,2.625 0.375,0.156 10 false WFL- 5.698,2.375 5.875,2.531 0.177,0.156 10 false 23 5.813,5.083 6.208,5.24 0.396,0.156 10 false L30 5.771,1.719 5.875,1.875 0.104,0.156 10 false 8 5.708,1.25 5.885,1.406 0.177,0.156 10 false 30 5.708,0.583 5.896,0.74 0.188,0.156 10 false 15 5.708,4.594 5.885,4.75 0.177,0.156 10 false 29 5.708,3.958 5.896,4.115 0.188,0.156 10 false 14 5.708,3.469 5.885,3.625 0.177,0.156 10 false 24 5.813,5.25 7.031,5.594 1.219,0.344 10 false Stereo Component Amplifier Assembly 0.448,5.583 1.667,5.927 1.219,0.344 10 false *1: for LHD 0.448,5.917 1.667,6.26 1.219,0.344 10 false *2: for RHD 1.875,2.938 1.979,3.094 0.104,0.156 10 false 1 1.875,3.583 1.979,3.74 0.104,0.156 10 false 2 1.875,4.052 1.979,4.208 0.104,0.156 10 false 1 1.875,4.688 1.979,4.844 0.104,0.156 10 false 2 1.875,0.74 1.979,0.896 0.104,0.156 10 false 1 1.875,1.844 1.979,2 0.104,0.156 10 false 1 1.875,2.479 1.979,2.635 0.104,0.156 10 false 2 1.875,1.375 1.979,1.531 0.104,0.156 10 false 2 0.333,3.146 1.615,3.802 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 0.333,2.969 0.646,3.125 0.313,0.156 10 false I6*2 0.333,2.813 0.646,2.969 0.313,0.156 10 false I4*1 0.333,4.292 1.615,4.948 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 0.333,4.125 0.635,4.281 0.302,0.156 10 false I7*2 0.333,3.948 0.635,4.104 0.302,0.156 10 false I5*1 0.333,0.927 1.615,1.583 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.333,0.76 0.594,0.917 0.26,0.156 10 false N1 0.333,2.031 1.615,2.688 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.323,1.854 0.583,2.01 0.26,0.156 10 false O1

E250488E03
5.948,0.719 6.344,0.875 0.396,0.156 10 false RR+ 5.948,1.365 6.323,1.521 0.375,0.156 10 false RR- 5.698,1.26 5.875,1.417 0.177,0.156 10 false 27 5.698,0.625 5.885,0.781 0.188,0.156 10 false 12 1.896,0.729 2,0.885 0.104,0.156 10 false 1 1.896,1.365 2,1.521 0.104,0.156 10 false 2 0.719,0.917 1.615,1.573 0.896,0.656 10 false Rear Speaker Assembly RH 0.719,0.75 0.979,0.906 0.26,0.156 10 false P3 5.948,1.833 6.25,1.99 0.302,0.156 10 false RL+ 5.948,2.469 6.208,2.625 0.26,0.156 10 false RL- 5.698,2.365 5.875,2.521 0.177,0.156 10 false 26 5.698,1.729 5.885,1.885 0.188,0.156 10 false 11 1.896,1.833 2,1.99 0.104,0.156 10 false 1 1.896,2.479 2,2.635 0.104,0.156 10 false 2 0.719,2.031 1.615,2.385 0.896,0.354 10 false Rear Speaker Assembly LH 0.708,1.854 0.969,2.01 0.26,0.156 10 false Q3 5.948,2.958 6.396,3.115 0.448,0.156 10 false TWR- 5.948,3.604 6.385,3.76 0.438,0.156 10 false TWR+ 5.698,3.479 5.875,3.635 0.177,0.156 10 false 13 5.698,2.844 5.885,3 0.188,0.156 10 false 28 1.896,2.958 2,3.115 0.104,0.156 10 false 1 1.896,3.583 2,3.74 0.104,0.156 10 false 2 0.313,3.146 1.552,3.531 1.24,0.385 10 false Rear No. 2 Speaker Assembly RH 0.313,2.969 0.573,3.125 0.26,0.156 10 false P5 5.948,4.063 6.354,4.219 0.406,0.156 10 false TWL- 5.969,4.698 6.385,4.854 0.417,0.156 10 false TWL+ 5.698,4.583 5.875,4.74 0.177,0.156 10 false 10 5.698,3.958 5.885,4.115 0.188,0.156 10 false 25 1.896,4.063 2,4.219 0.104,0.156 10 false 1 1.896,4.708 2,4.865 0.104,0.156 10 false 2 0.365,4.302 1.615,4.635 1.25,0.333 10 false Rear No. 2 Speaker Assembly LH 0.365,4.125 0.646,4.281 0.281,0.156 10 false Q5 5.833,5.125 6.229,5.281 0.396,0.156 10 false L30 5.833,5.292 7.052,5.948 1.219,0.656 10 false Stereo Component Amplifier Assembly


PROCEDURE

1.CONFIRM MODEL
Result:
Result Proceed to
for 6 Speakers A
for 8 Speakers B



A

2.CHECK HARNESS AND CONNECTOR

B

7.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the L36 and L41 radio and display receiver assembly connectors.


b.

Disconnect the N1 and O1 front No. 1 speaker assembly connectors.


c.

Disconnect the I2 and I3 front No. 2 speaker assembly connectors.


d.

Disconnect the P3 and Q3 rear speaker assembly connectors.


e.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L36-1 (FR+) - I2-2 (+) Always Below 1 Ω
L36-5 (FR-) - I2-4 (-) Always Below 1 Ω
L36-2 (FL+) - I3-2 (+) Always Below 1 Ω
L36-6 (FL-) - I3-4 (-) Always Below 1 Ω



f.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (+) - N1-1 Always Below 1 Ω
I2-3 (-) - N1-2 Always Below 1 Ω
I3-1 (+) - O1-1 Always Below 1 Ω
I3-3 (-) - O1-2 Always Below 1 Ω



g.

Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L41-1 (RR+) - P3-1 Always Below 1 Ω
L41-3 (RR-) - P3-2 Always Below 1 Ω
L41-2 (RL+) - Q3-1 Always Below 1 Ω
L41-6 (RL-) - Q3-2 Always Below 1 Ω



h.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L36-1 (FR+) - Body ground Always 10 kΩ or higher
L36-5 (FR-) - Body ground Always 10 kΩ or higher
L36-2 (FL+) - Body ground Always 10 kΩ or higher
L36-6 (FL-) - Body ground Always 10 kΩ or higher
L41-1 (RR+) - Body ground Always 10 kΩ or higher
L41-3 (RR-) - Body ground Always 10 kΩ or higher
L41-2 (RL+) - Body ground Always 10 kΩ or higher
L41-6 (RL-) - Body ground Always 10 kΩ or higher



i.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (+) - Body ground Always 10 kΩ or higher
I2-3 (-) - Body ground Always 10 kΩ or higher
I3-1 (+) - Body ground Always 10 kΩ or higher
I3-3 (-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Resistance check

i.
U191280E02
0.531,2.052 0.823,2.219 0.292,0.167 10 false O1 0.531,1.677 0.823,1.844 0.292,0.167 10 false N1 0.094,0.094 0.271,0.26 0.177,0.167 10 false *a 0.958,1.656 1.135,1.823 0.177,0.167 10 false *A 0.958,2.021 1.135,2.188 0.177,0.167 10 false *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 - N1-2 Always 3.2 to 4.8 Ω
O1-1 - O1-2 Always 3.2 to 4.8 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)




OK

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Resistance check

i.
U191327E01
0.094,0.079 0.248,0.226 0.154,0.147 10 *a 1.959,0.724 2.203,0.899 0.244,0.175 10 *A 1.959,1.059 2.203,1.234 0.244,0.175 10 *B 1.623,0.722 1.836,0.885 0.213,0.163 10 I2 1.623,1.066 1.826,1.229 0.202,0.163 10 I3 2.598,2.308 2.752,2.455 0.154,0.147 10 + 2.082,2.308 2.236,2.455 0.154,0.147 10 + 1.498,2.308 1.610,2.455 0.112,0.147 10 - 0.994,2.308 1.106,2.455 0.112,0.147 10 - 1.4,1.8 1.045,2.292 false 1.675,1.817 1.543,2.287 false 2.242,1.794 2.609,2.308 false 1.99,1.8 2.122,2.292 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-2 (+) - I2-4 (-) Always 10 kΩ or higher
I2-1 (+) - I2-2 (+) Always Below 1 Ω
I2-3 (-) - I2-4 (-) Always Below 1 Ω
I3-2 (+) - I3-4 (-) Always 10 kΩ or higher
I3-1 (+) - I3-2 (+) Always Below 1 Ω
I3-3 (-) - I3-4 (-) Always Below 1 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)




OK

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.





OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

6.INSPECT REAR SPEAKER ASSEMBLY
6.INSPECT REAR SPEAKER ASSEMBLY
a.

Resistance check

i.
U191278E02
0.635,2.031 0.927,2.198 0.292,0.167 10 false Q3 0.635,1.656 0.927,1.823 0.292,0.167 10 false P3 0.094,0.073 0.271,0.24 0.177,0.167 10 false *a 1.073,1.656 1.25,1.823 0.177,0.167 10 false *A 1.073,2.021 1.25,2.188 0.177,0.167 10 false *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-1 - P3-2 Always 3.2 to 4.8 Ω
Q3-1 - Q3-2 Always 3.2 to 4.8 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the N1 and O1 front No. 1 speaker assembly connectors.


c.

Disconnect the I4 and I5 front No. 2 speaker assembly connectors (for LHD).


d.

Disconnect the I6 and I7 front No. 2 speaker assembly connectors (for RHD).


e.

Disconnect the P3 and Q3 rear speaker assembly connectors.


f.

Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.


g.

Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - N1-1 Always Below 1 Ω
L30-30 (WFR-) - N1-2 Always Below 1 Ω
L30-8 (WFL+) - O1-1 Always Below 1 Ω
L30-23 (WFL-) - O1-2 Always Below 1 Ω



h.

Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L30-9 (FR+) - I4-1 Always Below 1 Ω
L30-24 (FR-) - I4-2 Always Below 1 Ω
L30-14 (FL+) - I5-1 Always Below 1 Ω
L30-29 (FL-) - I5-2 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L30-9 (FR+) - I6-1 Always Below 1 Ω
L30-24 (FR-) - I6-2 Always Below 1 Ω
L30-14 (FL+) - I7-1 Always Below 1 Ω
L30-29 (FL-) - I7-2 Always Below 1 Ω



i.

Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-12 (RR+) - P3-1 Always Below 1 Ω
L30-27 (RR-) - P3-2 Always Below 1 Ω
L30-11 (RL+) - Q3-1 Always Below 1 Ω
L30-26 (RL-) - Q3-2 Always Below 1 Ω



j.

Measure the resistance between the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-13 (TWR+) - P5-2 Always Below 1 Ω
L30-28 (TWR-) - P5-1 Always Below 1 Ω
L30-10 (TWL+) - Q5-2 Always Below 1 Ω
L30-25 (TWL-) - Q5-1 Always Below 1 Ω



k.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - Body ground Always 10 kΩ or higher
L30-30 (WFR-) - Body ground Always 10 kΩ or higher
L30-8 (WFL+) - Body ground Always 10 kΩ or higher
L30-23 (WFL-) - Body ground Always 10 kΩ or higher
L30-9 (FR+) - Body ground Always 10 kΩ or higher
L30-24 (FR-) - Body ground Always 10 kΩ or higher
L30-14 (FL+) - Body ground Always 10 kΩ or higher
L30-29 (FL-) - Body ground Always 10 kΩ or higher
L30-12 (RR+) - Body ground Always 10 kΩ or higher
L30-27 (RR-) - Body ground Always 10 kΩ or higher
L30-11 (RL+) - Body ground Always 10 kΩ or higher
L30-26 (RL-) - Body ground Always 10 kΩ or higher
L30-13 (TWR+) - Body ground Always 10 kΩ or higher
L30-28 (TWR-) - Body ground Always 10 kΩ or higher
L30-10 (TWL+) - Body ground Always 10 kΩ or higher
L30-25 (TWL-) - Body ground Always 10 kΩ or higher




OK

8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
U191280E02
0.531,2.052 0.823,2.219 0.292,0.167 10 false O1 0.531,1.677 0.823,1.844 0.292,0.167 10 false N1 0.094,0.094 0.271,0.26 0.177,0.167 10 false *a 0.958,1.656 1.135,1.823 0.177,0.167 10 false *A 0.958,2.021 1.135,2.188 0.177,0.167 10 false *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 - N1-2 Always 4.6 to 6.6 Ω
O1-1 - O1-2 Always 4.6 to 6.6 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)




OK

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
U191266E02
0.438,1.333 0.573,1.49 0.135,0.156 10 false I4 0.813,1.344 1.01,1.521 0.198,0.177 10 false *A 0.448,1.708 0.583,1.865 0.135,0.156 10 false I5 0.813,1.729 1.021,1.917 0.208,0.188 10 false *B 0.438,2.083 0.573,2.24 0.135,0.156 10 false I6 0.813,2.094 1.042,2.26 0.229,0.167 10 false *C 0.438,2.458 0.573,2.615 0.135,0.156 10 false I7 0.813,2.479 1.021,2.656 0.208,0.177 10 false *D 0.167,0.125 0.354,0.344 0.188,0.219 10 false *a

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I4-1 - I4-2 Always 10 kΩ or higher
I5-1 - I5-2 Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I6-1 - I6-2 Always 10 kΩ or higher
I7-1 - I7-2 Always 10 kΩ or higher


Text in Illustration
*A for RH (for LHD)
*B for LH (for LHD)
*C for RH (for RHD)
*D for LH (for RHD)
*a Component without harness connected
(Front No. 2 Speaker Assembly)




OK

10.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

10.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.





OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

11.INSPECT REAR SPEAKER ASSEMBLY
11.INSPECT REAR SPEAKER ASSEMBLY
a.
U191279E02
0.594,1.74 0.885,1.906 0.292,0.167 10 false P3 0.594,2.104 0.885,2.271 0.292,0.167 10 false Q3 1.01,1.74 1.188,1.906 0.177,0.167 10 false *A 1.01,2.135 1.188,2.302 0.177,0.167 10 false *B 0.115,0.125 0.292,0.292 0.177,0.167 10 false *a

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-1 - P3-2 Always 3.2 to 5.2 Ω
Q3-1 - Q3-2 Always 3.2 to 5.2 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)




OK

12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.
U191371E02
0.594,1.625 0.833,1.802 0.24,0.177 10 false P5 0.969,1.625 1.208,1.802 0.24,0.177 10 false *A 0.969,2.063 1.208,2.24 0.24,0.177 10 false *B 0.594,2.042 0.802,2.219 0.208,0.177 10 false Q5 0.25,0.146 0.438,0.365 0.188,0.219 10 false *a

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P5-1 - P5-2 Always 10 kΩ or higher
Q5-1 - Q5-2 Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear No. 2 Speaker Assembly)




OK

13.REPLACE REAR NO. 2 SPEAKER ASSEMBLY

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY

13.REPLACE REAR NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.





OK

END (REAR NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE