If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK).
Perform the operation check above and determine the speaker that is not operating.
| Result | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the L167 radio and display receiver assembly connector.
Disconnect the I2 and I3 front No. 2 speaker assembly connectors.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L167-1 (FR+) - I2-2 (+) | Always | Below 1 Ω |
| L167-5 (FR-) - I2-4 (-) | Always | Below 1 Ω |
| L167-2 (FL+) - I3-2 (+) | Always | Below 1 Ω |
| L167-6 (FL-) - I3-4 (-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I2-1 (+) - N1-1 | Always | Below 1 Ω |
| I2-3 (-) - N1-2 | Always | Below 1 Ω |
| I3-1 (+) - O1-1 | Always | Below 1 Ω |
| I3-3 (-) - O1-2 | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L167-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| L167-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| L167-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| L167-6 (FL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I2-1 (+) - Body ground | Always | 10 kΩ or higher |
| I2-3 (-) - Body ground | Always | 10 kΩ or higher |
| I3-1 (+) - Body ground | Always | 10 kΩ or higher |
| I3-3 (-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 2 speaker assembly (See Page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (+) - 4 (-) | Always | 10 kΩ or higher |
| 3 (-) - 4 (-) | Always | Below 1 Ω |
| 1 (+) - 2 (+) | Always | Below 1 Ω |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
OK
NG
Check that the malfunction disappears when a new or known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
OK
NG
Disconnect the L166 radio and display receiver assembly connector.
Disconnect the P3 and Q3 rear speaker assembly connectors.
Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L166-1 (RR+) - P3-1 | Always | Below 1 Ω |
| L166-3 (RR-) - P3-2 | Always | Below 1 Ω |
| L166-2 (RL+) - Q3-1 | Always | Below 1 Ω |
| L166-6 (RL-) - Q3-2 | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L166-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| L166-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| L166-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| L166-6 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the rear speaker assembly (See Page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Rear Speaker Assembly) |
OK
NG