Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  OPERATION CHECK  


CHECK PANEL & STEERING SWITCH


HINT:
·

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E296342

Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.


d.
E225786E01
2.269,1.407 3.085,1.407 false 0.344,1.149 1.04,1.149 false 2.888,1.063 3.085,1.063 false 0.148,1.048 0.304,1.200 0.156,0.152 10 *a 3.087,0.962 3.243,1.114 0.156,0.152 10 *b 3.087,1.327 3.243,1.480 0.156,0.152 10 *c

Panel & Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed.
*b: Number of switches pushed
·

Number of switches pushed at once is displayed.

·

If more than 3 switches are pushed at once, "More than 3" is displayed.

·

If 4 or more switches are pushed at once, "More than 3" is displayed.


*c: Rotary switch direction Direction of rotary switch is displayed.

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "SET UP"*1 or "APPS"*2 switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


*1: w/ DAB Function

*2: w/ Toyota Link Function





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E296343

Select "Touch Switch" from the "Function Check/Setting I" screen.


d.
E176521

Touch Switch Check

i.

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after your finger is removed.






CHECK MICROPHONE


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E296344

Select "Microphone Check" from the "Function Check/Setting I" screen.


d.
E277821E20
2.823,0.875 3.042,0.875 false 3.073,0.771 3.281,1 0.208,0.229 10 false *a

Microphone Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.





CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E296345

Select "Vehicle Signal" from the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Battery voltage is displayed.
IG Power switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with)/BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the radio and display receiver assembly.

·

This screen is updated once per second.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK HANDS-FREE VOICE QUALITY SETTING


HINT:
·

The hands-free voice quality of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E296346

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E268475E03
2.877,0.968 3.013,0.811 3.013,0.811 3.14,0.811 false 3.162,0.725 3.369,0.913 0.207,0.187 10 *a 2.752,1.586 2.937,1.824 2.937,1.824 3.064,1.824 false 1.809,1.586 1.683,1.858 1.683,1.858 1.556,1.858 false 3.086,1.738 3.293,1.926 0.207,0.187 10 *b 1.32,1.773 1.528,1.960 0.207,0.187 10 *c

Hands-Free Voice Quality Setting

Text in Illustration
*a Numeric Keypad
*b Setting Button
*c Reset Button

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A
(Noise)
The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
B
(Noise)
The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
C
(Echo)
The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).
D
(Echo)
The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).

Settings (When Multiple Phenomenon Occurred)
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A+C The other party hears background noise and weak echoes when listening to your voice. 1100
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


A+D The other party hears background noise and strong echoes when listening to your voice. 1200
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).


B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).



HINT:
·

The default value is "0000".

·

Settings will be applied when the setting button is selected.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by selecting "INIT".






CHECK DAB RECEPTION (w/ DAB Function)


HINT:
·

The reception condition of Digital Audio Broadcast (DAB) can be checked.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E268454

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E287047

Select "Next Page" from the "Function Check/ Setting I" screen.


d.
E235721

Select "DAB Reception Check" from the "Function Check/Setting II" screen.


e.
E245217E20
0.542,0.844 0.302,0.844 false 3.063,1.188 2.688,1.188 false 3.063,1.354 2.688,1.354 false 2.115,0.833 1.74,0.833 false 0.083,0.75 0.271,0.938 0.188,0.188 10 false *a 3.083,1.292 3.271,1.479 0.188,0.188 10 false *d 3.083,1.073 3.271,1.26 0.188,0.188 10 false *c 2.146,0.729 2.333,0.917 0.188,0.188 10 false *b

DAB Reception Check

Screen Description
Display Content
*a: Up or down switch Enables the channel to be changed to the one to be checked.
*b: Check/STOP switch
·

Check: Starts checking

·

STOP: Stops checking


*c: Antenna connection check DAB antenna connection status as follows:
·

OK: Connected properly

·

NG: Not connected properly

·

-: Not equipped with DAB antenna.


*d: DAB Tuner Reception Level Check Result Description Displays DAB antenna reception levels as follows:
·

111 or more: Font color is black (good reception)

·

110 or less: Font color is red (poor reception)

·

-: Not equipped with DAB antenna.



i.

Select "Check" to start the DAB reception check.


ii.

Check the results displayed when the DAB reception check is completed.

HINT:

If the reception level is abnormal, the antenna system or radio and display receiver assembly is malfunctioning.





CHECK SPEAKER


HINT:
·

This function is used when checking the speaker wiring and whether the speakers are functioning properly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Turn audio mode on and play any audio source.

HINT:

This audio source will be used for the speaker check.




c.
E268484

Select "Failure Diagnosis" from the "Service Menu" screen.


d.
E268489

Select "System Check" from the "Failure Diagnosis" screen.


e.
E268474

Select "SP Check ON" from the "System Check Mode" screen.


f.

Check the speaker wiring and check that the speakers are functioning properly.

HINT:
·

Check that each speaker outputs sound from the selected audio source properly.

·

"SP Check OFF" is displayed during the speaker check.

·

Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

·

More than one speaker may sound simultaneously depending on the speaker wiring.




g.

Sound stops when any of the following conditions are met:

i.

"SP Check OFF" is selected.


ii.

The power switch is turned off.


iii.

Diagnostic mode is turned off.


iv.

The screen is changed to another screen.


v.

Audio mode is turned off.




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the radio and display receiver assembly screen is blacked out.


a.

Check Software Error History.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


v.

When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.





b.

Clear software error history.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause of an optical disc error.


a.

Check Optical Disc Error History.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table (See page (Click here))
Disc damaged/upside down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted upside down.


Cannot determine disc type An unsuitable disc is inserted.
DPS error When an error occurs while decoding MP3/WMA/AAC files.
Some files are corrupt
·

When MP3/WMA/AAC files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA/AAC files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Not available
CD-P Radio and display receiver assembly
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.





b.

Clear optical disc error history.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





TOYOTA LINK RESET PROCEDURE (w/ Toyota Link Function)


a.

Duplicate the problem symptom.


b.

Check for DTCs and repair the systems for which any DTCs are output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).


c.

Check cellular phone compatibility.

i.

Check if the cellular phone/vehicle are compatible (Refer to http://www.toyota.com.au/owners).


ii.

If the cellular phone is not compatible, recommend to the customer a compatible cellular phone.



d.

Delete all paired devices from the cellular phone.

i.

This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



e.

Remove the Toyota Link app from the phone.

NOTICE:

Only perform this step if the customer is present and approves.


i.

The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



f.

Reset the phone.

NOTICE:

Only perform this step if the customer is present and approves.


i.

Turn off the phone and remove the battery for 15 seconds. For instructions on how to reset a cellular device, refer to the appropriate manufacturer's website.



g.

Reinstall the Toyota Link app on the phone. (If removed.)

i.

This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



h.

Delete all personal data from the head unit.

i.

Delete all personal data from the head unit.

NOTICE:

Only perform this step if the customer is present and approves.


HINT:

Re-installation of applications must be completed before applications will appear on the head unit.




i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


i.

Record all radio station presets.


ii.

Disconnect the cable from the negative (-) auxiliary battery terminal and leave it disconnected for 2 minutes.



j.

Check if the problem symptom disappears.