Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2014.11–2015.08
RM2070E _V1 General _061901 INTRODUCTION _0301450 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN AUXILIARY BATTERY TERMINAL IS DISCONNECTED/RECONNECTED


Necessary Procedures Effect / Inoperative Function when Necessary Procedure not Performed See Page
Correct the steering angle neutral point Intelligent parking assist system (Click here)
Back door lock Power door lock control system (Click here)

NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 90 seconds*1 or 120 seconds*2*4 before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

After the power switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 90 seconds*3 before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When the auxiliary battery is replaced or the cable is disconnected from its negative (-) auxiliary battery terminal, the ISC learning value will be initialized and symptoms as a loud rattle from the hybrid vehicle transaxle assembly may occur until ISC learning is performed. Therefore, perform ISC learning when the auxiliary battery is replaced or the cable is disconnected from the negative (-) terminal of the auxiliary battery (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Loud Rattle from Hybrid Vehicle Transmission).


*1: w/ Audio and Visual System (for Toyota Link Function)

*2: w/ Audio and Visual System (for DAB Function)

*3: w/ Navigation System (for Navigation Receiver Type)

*4: w/ Navigation System (for Radio and Display Type)




PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedure not Performed See Page
·

Hybrid vehicle control ECU

·

Hybrid battery junction block assembly


Current sensor offset learning - (Click here)
HV battery
1.

Prediagnostic battery charge

2.

Battery diagnosis


HV battery status information can not be updated (Click here)
Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system)
·

Dynamic radar cruise control system

·

Pre-crash safety system


(Click here)
Lane departure warning camera Adjust lane departure warning camera Lane departure alert system (Click here)
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Transmitter ID registration

·

Initialization


·

When DTC detection conditions of "transmitter ID not received" are met, TPWS indicator blinks for 1 minute, and then illuminates

·

Tire pressure warning function


(Click here) for initialization
(Click here) for registration
Brake booster with master cylinder (Skid control ECU, brake actuator or pressure sensor)
1.

Initialization and calibration of the linear solenoid valve

2.

Yaw rate and acceleration sensor zero point calibration


·

ABS warning light illumination

·

Slip indicator light illumination

·

Brake warning light / yellow (minor malfunction) illumination

·

VSC disabled or malfunctioning


(Click here) for initialization
(Click here) for calibration
·

Brake pedal stroke sensor

·

Brake pedal


1.

Clearing stored linear solenoid valve calibration data

2.

Initialization and calibration of the linear solenoid valve


·

ABS warning light illumination

·

Slip indicator light illumination

·

Brake warning light / yellow (minor malfunction) illumination

·

VSC disabled or malfunctioning


Yaw rate and acceleration sensor
1.

Clearing zero point calibration data

2.

Yaw rate and acceleration sensor zero point calibration


·

ABS warning light illumination

·

Slip indicator light illumination

·

Brake warning light / yellow (minor malfunction) illumination

·

VSC disabled or malfunctioning


Power steering ECU assembly
·

Rotation angle sensor value initialization and torque sensor zero point calibration

·

Assist map writing


·

EPS warning light comes on

·

EPS control


(Click here)
Steering column assembly Rotation angle sensor value initialization and torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right
Spiral cable with sensor sub-assembly
·

Correct steering angle neutral point

·

Steering angle setting


Intelligent parking assist system (Click here)
Parking assist ECU Parking assist ECU initialization Intelligent parking assist system
Rear television camera assembly Rear television camera optical axis adjustment (Camera position setting) Intelligent parking assist system
Rear height control sensor sub-assembly RH
·

Height control sensor vehicle height difference setting (Height set)

·

Rear television camera optical axis adjustment (Camera position setting)

·

Lighting system initialization


·

Intelligent parking assist system

·

Automatic headlight beam level control system


Rear bumper cover Rear bumper position (BUMPER) Intelligent parking assist system
Suspension, tires, etc.
·

Height control sensor vehicle height difference setting (Height set)

·

Rear television camera optical axis adjustment (Camera position setting)


Intelligent parking assist system
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)

·

Transmission control ECU assembly

·

Key


Code registration (Engine immobiliser system)
·

Wireless door lock control system

·

Entry and start system

·

Hybrid control system start


See the Service Bulletin for the registration method
·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 1 blower damper servo sub-assembly


Initialization servo motor (Air conditioning system) DTCs are output (Click here)
·

Roof sunshade ECU (sliding roof drive gear sub-assembly)

·

Roof sunshade

·

Roof sunshade housing


Initialize roof sunshade ECU (sliding roof drive gear sub-assembly)
·

Auto open and close function

·

Jam protection function

·

Door lock linked close function


(Click here)
·

Power window regulator motor assembly

·

Door window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto UP/DOWN function

·

Jam protection function

·

Remote control function

·

Operation function after power switch is turned off

·

Catch protection function


(Click here)
Headlight leveling ECU assembly Perform headlight leveling ECU assembly initialization Automatic headlight beam level control function (Click here)