Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.


WIRING DIAGRAM

E227677E65
0.219,3.115 0.635,3.26 0.417,0.146 10 false U3 0.229,3.281 2.198,3.823 1.969,0.542 10 false Map Light Assembly (Telephone Microphone Assembly) 5.677,3.115 6,3.26 0.323,0.146 10 false L35 5.677,3.292 6.885,3.625 1.208,0.333 10 false Radio and Display Receiver Assembly 5.75,1.167 5.854,1.313 0.104,0.146 10 false 5 5.927,1.25 6.313,1.396 0.385,0.146 10 false MIN+ 5.75,0.688 5.854,0.833 0.104,0.146 10 false 4 5.927,0.781 6.354,0.927 0.427,0.146 10 false MACC 5.688,1.635 5.875,1.781 0.188,0.146 10 false 19 5.927,1.729 6.313,1.875 0.385,0.146 10 false MIN- 5.688,2.115 5.875,2.26 0.188,0.146 10 false 18 5.927,2.208 6.354,2.354 0.427,0.146 10 false SGND 5.76,2.604 5.865,2.75 0.104,0.146 10 false 6 5.927,2.688 6.323,2.833 0.396,0.146 10 false SNS2 1.333,2.604 1.51,2.75 0.177,0.146 10 false 5 1.333,0.688 1.51,0.833 0.177,0.146 10 false 2 1.333,1.167 1.51,1.313 0.177,0.146 10 false 3 1.333,1.635 1.51,1.781 0.177,0.146 10 false 4 0.885,2.688 1.271,2.833 0.385,0.146 10 false SNS2 0.823,0.781 1.302,0.927 0.479,0.146 10 false MACC 0.833,1.25 1.271,1.396 0.438,0.146 10 false MCO+ 0.844,1.729 1.302,1.875 0.458,0.146 10 false MCO- 2.51,2.333 3.167,2.479 0.656,0.146 10 false (Shielded) 4.021,2.333 4.677,2.479 0.656,0.146 10 false (Shielded)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L35-4 (MACC) - U3-2 (MACC) Always Below 1 Ω
L35-5 (MIN+) - U3-3 (MCO+) Always Below 1 Ω
L35-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L35-6 (SNS2) - Body ground Always 10 kΩ or higher
L35-4 (MACC) - Body ground Always 10 kΩ or higher
L35-5 (MIN+) - Body ground Always 10 kΩ or higher
L35-19 (MIN-) - Body ground Always 10 kΩ or higher
L35-18 (SGND) - Body ground Always 10 kΩ or higher




OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the L35 radio and display receiver assembly connector.


b.

Reconnect the U3 map light assembly (telephone microphone assembly) connector.


c.
U191366E02
2.229,1.969 2.573,2.573 false 2.063,1.969 1.313,2.594 false 2.229,1.76 2.813,1.208 false 0.156,0.083 0.365,0.302 0.208,0.219 10 false *a 1.594,0.719 1.844,0.875 0.25,0.156 10 false L35 2.417,2.615 2.833,2.813 0.417,0.198 10 false SGND 2.875,1.042 3.323,1.24 0.448,0.198 10 false MACC 1.125,2.615 1.5,2.813 0.375,0.198 10 false MIN-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L35-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-18 (SGND) - Body ground Always Below 1 Ω
L35-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


b.
U191249E02
1.76,1.208 1.531,0.719 1.531,0.719 1.448,0.719 false 1.896,1.219 2.052,0.729 2.052,0.729 2.156,0.729 false 0.438,1.177 0.719,1.354 0.281,0.177 10 false U3 0.156,0.063 0.354,0.26 0.198,0.198 10 false *a 1,0.625 1.417,0.823 0.417,0.198 10 false SNS2 2.219,0.635 2.646,0.833 0.427,0.198 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U3-5 (SNS2) - U3-4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the L35 radio and display receiver assembly connector.


b.

Reconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.

Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the U3 map light assembly (telephone microphone assembly) connector.


e.
U191251E01
1.627,0.583 1.897,0.764 0.270,0.181 10 U3 0.175,0.152 0.373,0.349 0.198,0.198 10 *a 2.619,1.22 3.079,1.418 0.460,0.198 10 MCO+ 0.87,1.138 1.299,1.335 0.429,0.198 10 MCO- 2.603,1.339 2.021,2.038 false 1.883,2.038 1.507,1.233 1.507,1.233 1.378,1.233 false

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output B


Text in Illustration
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur
(returns to normal)
A
Malfunction recurs B




A

END

B

REPLACE MAP LIGHT ASSEMBLY