This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Stereo component amplifier assembly |
Disconnect the L30 stereo component amplifier assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the I4 and I5 front No. 2 speaker assembly connectors (for LHD).
Disconnect the I6 and I7 front No. 2 speaker assembly connectors (for RHD).
Disconnect the P3 and Q3 rear speaker assembly connectors.
Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L30-15 (WFR+) - Body ground | Always | 10 kΩ or higher |
| L30-30 (WFR-) - Body ground | Always | 10 kΩ or higher |
| L30-8 (WFL+) - Body ground | Always | 10 kΩ or higher |
| L30-23 (WFL-) - Body ground | Always | 10 kΩ or higher |
| L30-9 (FR+) - Body ground | Always | 10 kΩ or higher |
| L30-24 (FR-) - Body ground | Always | 10 kΩ or higher |
| L30-14 (FL+) - Body ground | Always | 10 kΩ or higher |
| L30-29 (FL-) - Body ground | Always | 10 kΩ or higher |
| L30-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| L30-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| L30-11 (RL+) - Body ground | Always | 10 kΩ or higher |
| L30-26 (RL-) - Body ground | Always | 10 kΩ or higher |
| L30-13 (TWR+) - Body ground | Always | 10 kΩ or higher |
| L30-28 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L30-10 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L30-25 (TWL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-1 - N1-2 | Always | 4.6 to 6.6 Ω |
| O1-1 - O1-2 | Always | 4.6 to 6.6 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
OK
NG
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-1 - I4-2 | Always | 10 kΩ or higher |
| I5-1 - I5-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-1 - I6-2 | Always | 10 kΩ or higher |
| I7-1 - I7-2 | Always | 10 kΩ or higher |
| *A | for RH (for LHD) |
| *B | for LH (for LHD) |
| *C | for RH (for RHD) |
| *D | for LH (for RHD) |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
OK
NG
Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
OK
NG
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P3-1 - P3-2 | Always | 3.2 to 5.2 Ω |
| Q3-1 - Q3-2 | Always | 3.2 to 5.2 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Rear Speaker Assembly) |
OK
NG
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P5-1 - P5-2 | Always | 10 kΩ or higher |
| Q5-1 - Q5-2 | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
OK
NG
Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
OK
NG