Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

·

The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the navigation ECU sub-assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation ECU sub-assembly.


WIRING DIAGRAM

E227677E66
0.271,3.083 0.552,3.229 0.281,0.146 10 false U3 0.271,3.25 2.281,3.594 2.01,0.344 10 false Map Light Assembly (Telephone Microphone Assembly) 5.771,3.115 6.094,3.26 0.323,0.146 10 false L38 5.76,1.125 5.865,1.271 0.104,0.146 10 false 5 5.927,1.271 6.313,1.417 0.385,0.146 10 false MIN+ 5.76,0.646 5.865,0.792 0.104,0.146 10 false 4 5.927,0.792 6.354,0.938 0.427,0.146 10 false MACC 5.688,1.604 5.875,1.75 0.188,0.146 10 false 19 5.927,1.75 6.313,1.896 0.385,0.146 10 false MIN- 5.688,2.073 5.875,2.219 0.188,0.146 10 false 18 5.927,2.229 6.354,2.375 0.427,0.146 10 false SGND 5.76,2.563 5.865,2.708 0.104,0.146 10 false 6 5.927,2.708 6.323,2.854 0.396,0.146 10 false SNS2 1.333,2.563 1.438,2.708 0.104,0.146 10 false 5 1.333,0.646 1.438,0.792 0.104,0.146 10 false 2 1.333,1.125 1.438,1.271 0.104,0.146 10 false 3 1.333,1.604 1.438,1.75 0.104,0.146 10 false 4 0.865,2.688 1.25,2.833 0.385,0.146 10 false SNS2 0.823,0.802 1.302,0.948 0.479,0.146 10 false MACC 0.833,1.26 1.271,1.406 0.438,0.146 10 false MCO+ 0.844,1.75 1.302,1.896 0.458,0.146 10 false MCO- 2.51,2.344 3.167,2.49 0.656,0.146 10 false (Shielded) 4.021,2.344 4.677,2.49 0.656,0.146 10 false (Shielded) 5.771,3.281 6.781,3.667 1.01,0.385 10 false Navigation ECU Sub-assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L38 navigation ECU sub-assembly connector.


b.

Disconnect the U3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-4 (MACC) - U3-2 (MACC) Always Below 1 Ω
L38-5 (MIN+) - U3-3 (MCO+) Always Below 1 Ω
L38-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L38-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L38-4 (MACC) - Body ground Always 10 kΩ or higher
L38-5 (MIN+) - Body ground Always 10 kΩ or higher
L38-19 (MIN-) - Body ground Always 10 kΩ or higher
L38-18 (SGND) - Body ground Always 10 kΩ or higher
L38-6 (SNS2) - Body ground Always 10 kΩ or higher




OK

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Reconnect the L38 navigation ECU sub-assembly connector.


b.

Reconnect the U3 map light assembly (telephone microphone assembly) connector.


c.
U191368E02
2.219,1.979 2.563,2.583 false 2.063,1.969 1.313,2.594 false 2.219,1.781 2.802,1.229 false 0.156,0.083 0.365,0.302 0.208,0.219 10 false *a 1.583,0.729 1.938,0.927 0.354,0.198 10 false L38 2.417,2.625 2.833,2.823 0.417,0.198 10 false SGND 2.854,1.083 3.302,1.281 0.448,0.198 10 false MACC 1.146,2.635 1.521,2.833 0.375,0.198 10 false MIN-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L38-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-18 (SGND) - Body ground Always Below 1 Ω
L38-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Navigation ECU Sub-assembly)



OK

NG

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the U3 map light assembly connector.


b.
U191247E02
1.771,1.25 1.51,1.656 false 1.906,1.25 2.167,1.656 false 1.615,0.354 1.896,0.531 0.281,0.177 10 false U3 0.156,0.063 0.354,0.26 0.198,0.198 10 false *a 1.25,1.667 1.667,1.865 0.417,0.198 10 false SNS2 2.021,1.677 2.448,1.875 0.427,0.198 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U3-5 (SNS2) - U3-4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the L38 navigation ECU sub-assembly connector.


b.
U191250E02
1.875,2.094 1.375,2.729 false 2.031,2.083 2.531,2.719 false 1.635,0.563 1.906,0.74 0.271,0.177 10 false U3 0.177,0.073 0.375,0.271 0.198,0.198 10 false *a 2.375,2.75 2.833,2.948 0.458,0.198 10 false MCO+ 1.083,2.74 1.51,2.938 0.427,0.198 10 false MCO-

Reconnect the U3 map light assembly connector.


c.

Turn the power switch on (ACC).


d.

Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the U3 map light assembly connector.


e.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output A
A waveform synchronized with the voice input to the map light assembly is not output B


Text in Illustration
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur
(returns to normal)
A
Malfunction recurs B




A

END

B

REPLACE MAP LIGHT ASSEMBLY