The navigation ECU sub-assembly receives a vehicle speed signal from the meter circuit plate and information from the navigation antenna assembly, and then adjusts the vehicle position.
The navigation ECU sub-assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the meter circuit plate becomes large.
A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls the respective systems based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C2 | A difference between the GPS speed and SPD pulse is detected. | ·
Navigation ECU sub-assembly ·
Meter circuit plate ·
Harness or connector ·
Junction connector |
Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).
While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.
The meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
OK
NG
Check the output waveform.
Remove the meter circuit plate with the connector(s) still connected.
Connect an oscilloscope to terminal L27-15 (+S) and body ground.
Turn the power switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | L27-15 (+S) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| *a | Component with harness connected
(Meter Circuit Plate) |
OK
NG
Check the input waveform.
Remove the navigation ECU sub-assembly with the connector(s) still connected.
Connect an oscilloscope to terminal L38-17 (SPD) and body ground.
Turn the power switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | L38-17 (SPD) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
OK
NG
Disconnect the L38 navigation ECU assembly connector.
Disconnect the L70 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L38-17 (SPD) - L70-3 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L38-17 (SPD) - L70-12 | Always | Below 1 Ω |
OK
NG