Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Navigation ECU sub-assembly

·

Harness or connector



WIRING DIAGRAM

E226160E37
0.588,2.016 2.619,2.392 2.031,0.376 10 Map Light Assembly (Telephone Microphone Assembly) 4.408,1.919 4.758,2.066 0.350,0.147 10 L38 4.408,2.109 6.393,2.276 1.985,0.167 10 Navigation ECU Sub-assembly 5.113,1.453 5.492,1.600 0.378,0.147 10 MIN- 5.113,0.655 5.533,0.829 0.420,0.174 10 SNS2 4.83,1.36 5.011,1.506 0.181,0.147 10 19 4.894,0.561 4.999,0.736 0.105,0.174 10 6 1.669,1.458 2.110,1.604 0.440,0.147 10 MCO- 1.67,0.652 2.082,0.827 0.412,0.174 10 SNS2 2.157,1.355 2.336,1.502 0.179,0.147 10 4 2.157,0.556 2.354,0.731 0.198,0.174 10 5 0.588,1.836 0.938,1.983 0.350,0.147 10 U3

PROCEDURE

1.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.
U191367E02
2.073,1.979 2.427,2.573 false 0.156,0.083 0.365,0.302 0.208,0.219 10 false *a 1.594,0.719 1.844,0.917 0.25,0.198 10 false L38 2.302,2.604 2.719,2.802 0.417,0.198 10 false MIN-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Navigation ECU Sub-assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L38 navigation ECU sub-assembly connector.


b.

Disconnect the U3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L38-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L38-6 (SNS2) - Body ground Always 10 kΩ or higher
L38-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.
U191246E02
1.76,1.25 1.5,1.656 false 1.896,1.25 2.156,1.656 false 1.604,0.354 1.885,0.531 0.281,0.177 10 false U3 0.156,0.063 0.354,0.26 0.198,0.198 10 false *a 1.25,1.677 1.667,1.875 0.417,0.198 10 false SNS2 2,1.677 2.427,1.875 0.427,0.198 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U3-5 (SNS2) - U3-4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

NG

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END

NG

REPLACE MAP LIGHT ASSEMBLY