Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E305056E14
2.042,1.292 2.135,1.438 0.094,0.146 10 false 2 2.042,1.844 2.135,1.99 0.094,0.146 10 false 1 2.198,1.385 2.49,1.531 0.292,0.146 10 false IL+2 2.198,1.958 2.51,2.104 0.313,0.146 10 false EAU 2.031,2.354 2.344,2.5 0.313,0.146 10 false SR2 0.083,2.365 1.583,2.51 1.5,0.146 10 false Steering Pad Switch LH 2.031,2.51 2.854,2.833 0.823,0.323 10 false Steering Pad Switch RH 3.271,1.177 3.365,1.323 0.094,0.146 10 false 5 3.24,1.365 3.427,1.51 0.188,0.146 10 false z9 4.156,1.188 4.333,1.333 0.177,0.146 10 false 12 4.125,1.375 4.417,1.521 0.292,0.146 10 false L52 3.625,1.292 3.917,1.438 0.292,0.146 10 false IL+2 3.271,1.75 3.365,1.896 0.094,0.146 10 false 8 3.24,1.938 3.427,2.083 0.188,0.146 10 false z9 4.198,1.75 4.375,1.896 0.177,0.146 10 false 4 4.125,1.948 4.417,2.094 0.292,0.146 10 false L52 3.625,1.854 3.938,2 0.313,0.146 10 false EAU 3.125,2.354 4.51,2.76 1.385,0.406 10 false Spiral Cable with Sensor Sub-assembly 2.542,0.333 3.719,0.688 1.177,0.354 10 false from TAIL Relay 4.438,0.927 4.75,1.073 0.313,0.146 10 false TAIL 4.365,0.49 4.844,0.635 0.479,0.146 10 false PANEL 3.927,3.344 4.188,3.49 0.26,0.146 10 false RL 2.792,3.552 3.073,3.698 0.281,0.146 10 false L27 2.781,3.719 5.021,3.958 2.24,0.24 10 false Combination Meter Sub-Assembly 5.823,3.813 7.146,4.198 1.323,0.385 10 false Radio and Display Receiver Assembly 4.208,3.24 4.427,3.385 0.219,0.146 10 false 34 6.281,3.344 6.542,3.49 0.26,0.146 10 false ILL- 5.99,3.146 6.083,3.292 0.094,0.146 10 false 5 5.885,3.344 6.281,3.49 0.396,0.146 10 false L166 6.302,1.385 6.594,1.531 0.292,0.146 10 false ILL+ 5.938,1.177 6.115,1.323 0.177,0.146 10 false 10 5.885,1.375 6.323,1.521 0.438,0.146 10 false L167 6.302,1.958 6.698,2.104 0.396,0.146 10 false SWG 5.969,1.75 6.146,1.896 0.177,0.146 10 false 23 5.927,1.948 6.188,2.094 0.26,0.146 10 false L35

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch. A
Illumination comes on for all components except radio and display receiver assembly. B
Illumination comes on only for steering pad switch. C
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). D




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

D

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the L52 spiral cable with sensor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-12 (IL+2) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V




OK

3.INSPECT STEERING PAD SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH LH
a.

Remove the steering pad switch LH (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).


b.

Connect a positive (+) lead from the auxiliary battery to terminal 2 (IL+2) and a negative (-) lead to terminal 1 (EAU) of the steering pad switch LH connector.

E305057E01
0.458,0.197 0.677,0.443 0.218,0.246 10 *a 3.208,1.453 3.586,1.633 0.378,0.180 10 IL+2 4.383,1.604 4.770,1.827 0.387,0.224 10 EAU 4.007,1.908 3.515,1.574 false 4.006,2.023 4.37,1.749 false

Text in Illustration
*a Component without harness connected
(Steering Pad Switch LH)
- -


c.

Check if the illumination for the steering pad switch LH comes on.

OK:

Illumination for the steering pad switch LH comes on.




OK

4.INSPECT STEERING PAD SWITCH RH

NG

REPLACE STEERING PAD SWITCH LH

4.INSPECT STEERING PAD SWITCH RH
a.

Remove the steering pad switch RH (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

U155190E02
3.563,2.656 3.448,3.094 false 3.802,2.49 4.167,2.219 false 1.75,1.385 1.854,1.594 false 1.563,1.375 1.354,1.635 false 0.219,0.135 0.438,0.385 0.219,0.25 10 false *a 4.271,2.479 4.479,2.667 0.208,0.188 10 false z9 3.313,3.104 3.688,3.281 0.375,0.177 10 false EAU 4.208,2.115 4.594,2.344 0.385,0.229 10 false IL+2 0.615,1.281 1,1.469 0.385,0.188 10 false SR2 1.188,1.667 1.563,1.844 0.375,0.177 10 false EAU 1.75,1.625 2.135,1.854 0.385,0.229 10 false IL+2

Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
SR2-2 (IL+2) - z9-5 (IL+2) Always Below 1 Ω
SR2-1 (EAU) - z9-8 (EAU) Always Below 1 Ω




OK

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH RH

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

E343935E02
3.5,0.667 3.917,0.917 0.417,0.25 3.583,3.583 4,3.833 0.417,0.25 3.74,1.438 4.208,1.188 false 3.479,1.292 3.208,1.135 false 3.771,4.26 3.354,4.438 false 4.042,4.094 4.219,3.885 false 1.979,0.229 2.292,0.427 0.313,0.198 10 false *a 2.875,0.656 3.104,0.854 0.229,0.198 10 false *b 2.969,3.594 3.198,3.792 0.229,0.198 10 false *c 3.646,0.708 3.896,0.906 0.25,0.198 10 false z9 3.667,3.625 3.958,3.823 0.292,0.198 10 false L52 2.896,1.01 3.229,1.219 0.333,0.208 10 false IL+2 4.25,1.094 4.583,1.302 0.333,0.208 10 false EAU 3.021,4.365 3.354,4.573 0.333,0.208 10 false EAU 4.26,3.729 4.594,3.938 0.333,0.208 10 false IL+2

Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Side
*c Vehicle Side

Standard Resistance:
Tester Connection Condition Specified Condition
z9-5 (IL+2) - L52-12 (IL+2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z9-8 (EAU) - L52-4 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-5 (IL+2) - L52-12 (IL+2) Always 3 Ω or less
z9-8 (EAU) - L52-4 (EAU) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.





OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the L167 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L167-10 (ILL+) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V




OK

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L166 radio and display receiver assembly connector.


b.

Disconnect the L27 combination meter sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L166-5 (ILL-) - L27-34 (RL) Always Below 1 Ω
L166-5 (ILL-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR