Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Speaker Circuit  


DESCRIPTION

for 6 Speakers:

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.


for 8 Speakers:

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.


WIRING DIAGRAM

for 6 Speakers


E230315E14
5.667,7.479 6.896,8.083 1.229,0.604 10 false Radio and Display Receiver Assembly 3.021,1.292 4.302,1.948 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 5.563,0.75 5.667,0.906 0.104,0.156 10 false 1 4.531,0.833 4.635,0.99 0.104,0.156 10 false 2 4.542,1.698 4.646,1.854 0.104,0.156 10 false 4 2.313,0.844 2.417,1 0.104,0.156 10 false 1 2.323,1.708 2.427,1.865 0.104,0.156 10 false 3 2.469,0.854 2.573,1.01 0.104,0.156 10 false + 2.469,1.698 2.573,1.854 0.104,0.156 10 false - 4.365,0.833 4.469,0.99 0.104,0.156 10 false + 4.396,1.688 4.5,1.844 0.104,0.156 10 false - 5.438,0.948 5.771,1.104 0.333,0.156 10 false L167 3.021,1.125 3.281,1.281 0.26,0.156 10 false I2 0.344,1.281 1.625,1.938 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.344,1.115 0.604,1.271 0.26,0.156 10 false N1 3.021,3.24 4.302,3.896 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 4.531,2.813 4.635,2.969 0.104,0.156 10 false 2 4.531,3.688 4.635,3.844 0.104,0.156 10 false 4 2.313,2.813 2.417,2.969 0.104,0.156 10 false 1 2.333,3.698 2.438,3.854 0.104,0.156 10 false 3 2.469,2.813 2.573,2.969 0.104,0.156 10 false + 2.469,3.688 2.573,3.844 0.104,0.156 10 false - 4.375,2.802 4.479,2.958 0.104,0.156 10 false + 4.385,3.677 4.49,3.833 0.104,0.156 10 false - 3.021,3.073 3.281,3.229 0.26,0.156 10 false I3 0.344,3.24 1.625,3.896 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.333,3.063 0.594,3.219 0.26,0.156 10 false O1 0.74,5.052 1.646,5.708 0.906,0.656 10 false Rear Speaker Assembly RH 0.74,4.896 1,5.052 0.26,0.156 10 false P3 0.74,6.563 1.646,7.219 0.906,0.656 10 false Rear Speaker Assembly LH 0.74,6.385 1,6.542 0.26,0.156 10 false Q3 5.438,1.823 5.771,1.979 0.333,0.156 10 false L167 5.438,2.917 5.771,3.073 0.333,0.156 10 false L167 5.438,3.792 5.771,3.948 0.333,0.156 10 false L167 5.438,4.844 5.781,5 0.344,0.156 10 false L166 5.438,5.469 5.792,5.625 0.354,0.156 10 false L166 5.438,6.354 5.792,6.51 0.354,0.156 10 false L166 5.427,6.99 5.781,7.146 0.354,0.156 10 false L166 5.844,0.948 6.135,1.104 0.292,0.156 10 false FR+ 5.844,1.823 6.104,1.979 0.26,0.156 10 false FR- 5.844,2.927 6.104,3.083 0.26,0.156 10 false FL+ 5.844,3.792 6.104,3.948 0.26,0.156 10 false FL- 5.844,4.844 6.146,5 0.302,0.156 10 false RR+ 5.844,5.479 6.125,5.635 0.281,0.156 10 false RR- 5.844,6.365 6.125,6.521 0.281,0.156 10 false RL+ 5.844,7 6.104,7.156 0.26,0.156 10 false RL- 5.552,6.802 5.656,6.958 0.104,0.156 10 false 6 5.542,6.156 5.646,6.313 0.104,0.156 10 false 2 5.552,5.26 5.656,5.417 0.104,0.156 10 false 3 5.552,4.646 5.656,4.802 0.104,0.156 10 false 1 5.552,3.573 5.656,3.729 0.104,0.156 10 false 6 5.552,2.708 5.656,2.865 0.104,0.156 10 false 2 5.552,1.615 5.656,1.771 0.104,0.156 10 false 5 1.792,1.083 1.896,1.24 0.104,0.156 10 false 1 1.792,1.698 1.896,1.854 0.104,0.156 10 false 2 1.792,3.042 1.896,3.198 0.104,0.156 10 false 1 1.792,3.688 1.896,3.844 0.104,0.156 10 false 2 1.792,4.844 1.896,5 0.104,0.156 10 false 1 1.792,5.479 1.896,5.635 0.104,0.156 10 false 2 1.792,6.365 1.896,6.521 0.104,0.156 10 false 1 1.792,7 1.896,7.156 0.104,0.156 10 false 2


for 8 Speakers


E241547E12
0.417,0.75 0.75,0.917 0.333,0.167 10 false N1 0.417,0.917 1.688,1.25 1.271,0.333 10 false Front No. 1 Speaker Assembly RH 1.917,0.719 2.083,0.885 0.167,0.167 10 false 1 1.917,1.375 2.083,1.542 0.167,0.167 10 false 2 1.917,1.854 2.083,2.021 0.167,0.167 10 false 1 1.917,2.969 2.083,3.135 0.167,0.167 10 false 1 1.917,4.073 2.083,4.24 0.167,0.167 10 false 1 1.917,2.469 2.083,2.635 0.167,0.167 10 false 2 1.917,3.583 2.083,3.75 0.167,0.167 10 false 2 1.917,4.688 2.083,4.854 0.167,0.167 10 false 2 0.417,1.854 0.75,2.021 0.333,0.167 10 false O1 0.417,2.021 1.688,2.354 1.271,0.333 10 false Front No. 1 Speaker Assembly LH 0.417,2.979 0.75,3.146 0.333,0.167 10 false I4 0.417,3.146 1.688,3.479 1.271,0.333 10 false Front No. 2 Speaker Assembly RH 0.417,4.25 1.688,4.583 1.271,0.333 10 false Front No. 2 Speaker Assembly LH 0.417,4.083 0.75,4.25 0.333,0.167 10 false I5 5.698,0.625 5.948,0.792 0.25,0.167 10 false 15 5.698,1.26 5.948,1.427 0.25,0.167 10 false 30 5.771,1.74 6.021,1.906 0.25,0.167 10 false 8 5.698,2.365 5.948,2.531 0.25,0.167 10 false 23 5.771,2.844 5.938,3.01 0.167,0.167 10 false 9 5.688,3.479 5.938,3.646 0.25,0.167 10 false 24 5.708,3.958 5.958,4.167 0.25,0.208 10 false 14 5.698,4.594 5.948,4.76 0.25,0.167 10 false 29 5.979,0.729 6.542,1 0.563,0.271 10 false WFR+ 5.979,1.354 6.448,1.563 0.469,0.208 10 false WFR- 5.979,1.844 6.531,2.083 0.552,0.24 10 false WFL+ 5.979,2.479 6.469,2.729 0.49,0.25 10 false WFL- 5.979,2.948 6.479,3.115 0.5,0.167 10 false FR+ 5.979,3.573 6.396,3.74 0.417,0.167 10 false FR- 5.979,4.063 6.396,4.229 0.417,0.167 10 false FL+ 5.979,4.688 6.396,4.854 0.417,0.167 10 false FL- 5.781,5.104 6.115,5.271 0.333,0.167 10 false L30 5.781,5.271 6.979,5.604 1.198,0.333 10 false Stereo Component Amplifier Assembly

E241548E06
5.958,0.708 6.354,0.865 0.396,0.156 10 false RR+ 5.958,1.375 6.333,1.531 0.375,0.156 10 false RR- 5.708,1.26 5.885,1.417 0.177,0.156 10 false 27 5.708,0.615 5.896,0.771 0.188,0.156 10 false 12 1.906,0.719 2.01,0.875 0.104,0.156 10 false 1 1.906,1.375 2.01,1.531 0.104,0.156 10 false 2 0.729,0.906 1.625,1.563 0.896,0.656 10 false Rear Speaker Assembly RH 0.729,0.729 0.99,0.885 0.26,0.156 10 false P3 5.958,1.844 6.26,2 0.302,0.156 10 false RL+ 5.958,2.469 6.219,2.625 0.26,0.156 10 false RL- 5.708,2.365 5.885,2.521 0.177,0.156 10 false 26 5.708,1.729 5.896,1.885 0.188,0.156 10 false 11 1.906,1.875 2.01,2.031 0.104,0.156 10 false 1 1.906,2.469 2.01,2.625 0.104,0.156 10 false 2 0.729,2.031 1.625,2.385 0.896,0.354 10 false Rear Speaker Assembly LH 0.729,1.865 0.99,2.021 0.26,0.156 10 false Q3 5.958,2.948 6.406,3.104 0.448,0.156 10 false TWR+ 5.958,3.604 6.354,3.76 0.396,0.156 10 false TWR- 5.708,3.469 5.885,3.625 0.177,0.156 10 false 28 5.708,2.844 5.896,3 0.188,0.156 10 false 13 1.906,2.979 2.01,3.135 0.104,0.156 10 false 1 1.906,3.583 2.01,3.74 0.104,0.156 10 false 2 0.302,3.125 1.615,3.5 1.313,0.375 10 false Rear No. 2 Speaker Assembly RH 0.302,2.948 0.563,3.104 0.26,0.156 10 false P5 5.958,4.063 6.365,4.219 0.406,0.156 10 false TWL+ 5.958,4.719 6.344,4.875 0.385,0.156 10 false TWL- 5.708,4.583 5.885,4.74 0.177,0.156 10 false 25 5.708,3.958 5.896,4.115 0.188,0.156 10 false 10 1.906,4.094 2.01,4.25 0.104,0.156 10 false 1 1.906,4.708 2.01,4.865 0.104,0.156 10 false 2 0.375,4.271 1.625,4.604 1.25,0.333 10 false Rear No. 2 Speaker Assembly LH 0.375,4.094 0.656,4.25 0.281,0.156 10 false Q5 5.844,5.115 6.24,5.271 0.396,0.156 10 false L30 5.833,5.281 7.052,5.938 1.219,0.656 10 false Stereo Component Amplifier Assembly


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for 6 Speakers A
for 8 Speakers B




A

2.CHECK SPEAKER (OPERATION CHECK)

B

9.CHECK SPEAKER (OPERATION CHECK)
2.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen.

Refer to Check Speaker in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>OPERATION CHECK).


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly A
Rear speaker assembly B


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the L167 radio and display receiver assembly connector.


b.

Disconnect the I2 and I3 front No. 2 speaker assembly connectors.


c.

Disconnect the N1 and O1 front No. 1 speaker assembly connectors.


d.

Measure the resistance between the radio and display receiver assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L167-1 (FR+) - I2-2 (+) Always Below 1 Ω
L167-5 (FR-) - I2-4 (-) Always Below 1 Ω
L167-2 (FL+) - I3-2 (+) Always Below 1 Ω
L167-6 (FL-) - I3-4 (-) Always Below 1 Ω



e.

Measure the resistance between each of the front No. 2 speaker assemblies and the front No. 1 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (+) - N1-1 Always Below 1 Ω
I2-3 (-) - N1-2 Always Below 1 Ω
I3-1 (+) - O1-1 Always Below 1 Ω
I3-3 (-) - O1-2 Always Below 1 Ω



f.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L167-1 (FR+) - Body ground Always 10 kΩ or higher
L167-5 (FR-) - Body ground Always 10 kΩ or higher
L167-2 (FL+) - Body ground Always 10 kΩ or higher
L167-6 (FL-) - Body ground Always 10 kΩ or higher



g.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (+) - Body ground Always 10 kΩ or higher
I2-3 (-) - Body ground Always 10 kΩ or higher
I3-1 (+) - Body ground Always 10 kΩ or higher
I3-3 (-) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).


b.
E289435E03
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Front No. 1 Speaker Assembly)



OK

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).


b.
E226097E63
0.094,0.079 0.248,0.226 0.154,0.147 10 *a 1.498,2.308 1.652,2.455 0.154,0.147 10 - 1.154,2.308 1.308,2.455 0.154,0.147 10 - 2.437,2.308 2.550,2.455 0.112,0.147 10 + 2.076,2.308 2.189,2.455 0.112,0.147 10 + 1.4,1.8 1.217,2.292 false 1.675,1.817 1.543,2.287 false 2.242,1.794 2.437,2.308 false 1.99,1.8 2.122,2.292 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 4 (-) Always 10 kΩ or higher
1 (+) - 2 (+) Always Below 1 Ω
3 (-) - 4 (-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front No. 2 Speaker Assembly)



OK

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a new or known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH side.





OK

END

NG

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the L166 radio and display receiver assembly connector.


b.

Disconnect the P3 and Q3 rear speaker assembly connectors.


c.

Measure the resistance between the radio and display receiver assembly and each of the rear speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L166-1 (RR+) - P3-1 Always Below 1 Ω
L166-3 (RR-) - P3-2 Always Below 1 Ω
L166-2 (RL+) - Q3-1 Always Below 1 Ω
L166-6 (RL-) - Q3-2 Always Below 1 Ω



d.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L166-1 (RR+) - Body ground Always 10 kΩ or higher
L166-3 (RR-) - Body ground Always 10 kΩ or higher
L166-2 (RL+) - Body ground Always 10 kΩ or higher
L166-6 (RL-) - Body ground Always 10 kΩ or higher




OK

8.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).


b.
E289435E03
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Rear Speaker Assembly)



OK

NG

9.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen.

Refer to Check Speaker in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>OPERATION CHECK).


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly B
Rear speaker assembly C
Rear No. 2 speaker assembly D


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

B

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)

D

16.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the N1 and O1 front No. 1 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the front No. 1 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - N1-1 Always Below 1 Ω
L30-30 (WFR-) - N1-2 Always Below 1 Ω
L30-8 (WFL+) - O1-1 Always Below 1 Ω
L30-23 (WFL-) - O1-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - Body ground Always 10 kΩ or higher
L30-30 (WFR-) - Body ground Always 10 kΩ or higher
L30-8 (WFL+) - Body ground Always 10 kΩ or higher
L30-23 (WFL-) - Body ground Always 10 kΩ or higher




OK

11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).


b.
E289435E05
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4.6 to 6.6 Ω


Text in Illustration
*a Component without harness connected
(Front No. 1 Speaker Assembly)



OK

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the I4 and I5 front No. 2 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-9 (FR+) - I4-1 Always Below 1 Ω
L30-24 (FR-) - I4-2 Always Below 1 Ω
L30-14 (FL+) - I5-1 Always Below 1 Ω
L30-29 (FL-) - I5-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-9 (FR+) - Body ground Always 10 kΩ or higher
L30-24 (FR-) - Body ground Always 10 kΩ or higher
L30-14 (FL+) - Body ground Always 10 kΩ or higher
L30-29 (FL-) - Body ground Always 10 kΩ or higher




OK

13.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).


b.
E187205E17
0.154,0.034 0.341,0.249 0.187,0.215 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Front No. 2 Speaker Assembly)



OK

NG

14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the P3 and Q3 rear speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the rear speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-12 (RR+) - P3-1 Always Below 1 Ω
L30-27 (RR-) - P3-2 Always Below 1 Ω
L30-11 (RL+) - Q3-1 Always Below 1 Ω
L30-26 (RL-) - Q3-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-12 (RR+) - Body ground Always 10 kΩ or higher
L30-27 (RR-) - Body ground Always 10 kΩ or higher
L30-11 (RL+) - Body ground Always 10 kΩ or higher
L30-26 (RL-) - Body ground Always 10 kΩ or higher




OK

15.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).


b.
E289435E02
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 5.2 Ω


Text in Illustration
*a Component without harness connected
(Rear Speaker Assembly)



OK

NG

16.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-13 (TWR+) - P5-1 Always Below 1 Ω
L30-28 (TWR-) - P5-2 Always Below 1 Ω
L30-10 (TWL+) - Q5-1 Always Below 1 Ω
L30-25 (TWL-) - Q5-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-13 (TWR+) - Body ground Always 10 kΩ or higher
L30-28 (TWR-) - Body ground Always 10 kΩ or higher
L30-10 (TWL+) - Body ground Always 10 kΩ or higher
L30-25 (TWL-) - Body ground Always 10 kΩ or higher




OK

17.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.

Remove the rear No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).


b.
E177897E92
0.182,0.133 0.380,0.303 0.198,0.170 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Rear No. 2 Speaker Assembly)



OK

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY