Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  OPERATION CHECK  


CHECK NAVIGATION SYSTEM NORMAL CONDITION


a.

If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

Symptom Answer
A longer route than expected is chosen. Depending on the road conditions, the navigation ECU may determine that a longer route is quicker.
Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
When the vehicle is put into motion immediately after the hybrid control system starts, the navigation system deviates from the correct position. If the vehicle starts before the navigation system activates, the system may not react.
When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. When the vehicle is driving on new roads not available on the internal memory, the system attempts to match it to another nearby road, causing the position mark to deviate.
Expected arrival time is earlier than current time, or time different from expected arrival time is displayed. If a destination is set to a point where a different time zone is used, the system displays an expected arrival time corresponding to the time zone of the destination. If a location on the sea is set as the destination, the system may display an expected arrival time corresponding to the time zone setting of the vehicle. Check which communication is not used for displaying traffic information.


b.
I100066

The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor or navigation ECU.

i.

The current position mark may be displayed on a nearby parallel road.


ii.
I100067

Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.


iii.
I100068

When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.


iv.
I100069

When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.


v.
I100070

When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.


vi.
I100071

When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.


vii.
I100072

When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.


viii.
E106418

When the power switch is turned on (ACC) or on (IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.


ix.
I100074

When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.


x.
I100075

When the tires are changed, the current vehicle position mark may deviate from the correct position.

HINT:
·

A change in tire diameter may cause a speed sensor error.

·

Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.






CHECK PANEL & STEERING SWITCH


HINT:
·

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Panel & Steering Switch.


c.
E225786E01
2.269,1.407 3.085,1.407 false 0.344,1.149 1.04,1.149 false 2.888,1.063 3.085,1.063 false 0.148,1.048 0.304,1.200 0.156,0.152 10 *a 3.087,0.962 3.243,1.114 0.156,0.152 10 *b 3.087,1.327 3.243,1.480 0.156,0.152 10 *c

Panel & Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If 3 switches are pushed at once, "3" or "More than 3" is displayed

·

If 4 or more switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Touch Switch.


c.
E176521

Touch Switch Check

i.

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after your finger is removed.






CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Vehicle Signal.


c.
E225776

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Auxiliary battery voltage is displayed.
IG Power switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with)/BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the radio and display receiver assembly.

·

This screen is updated once per second.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK MICROPHONE


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Next Page > EXT BOX > Microphone Check.


c.
E277821E19
2.823,0.875 3.042,0.875 false 3.073,0.771 3.281,1 0.208,0.229 10 false *a

Microphone Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.





CHECK SYSTEM SENSORS


HINT:
·

GPS information, vehicle signals and sensor signals are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Next Page > EXT BOX > System Sensors Check.


c.
E283415E08
0.354,1.51 0.594,1.51 false 0.354,1.344 0.646,1.344 false 0.365,0.719 0.656,0.719 false 2.865,1.646 3.146,1.646 false 1.854,1.885 1.854,1.563 false 0.198,0.615 0.51,0.813 0.313,0.198 10 false *a 0.188,1.25 0.5,1.448 0.313,0.198 10 false *b 0.177,1.417 0.49,1.615 0.313,0.198 10 false *c 1.771,1.906 2.083,2.104 0.313,0.198 10 false *d 3.177,1.552 3.354,1.75 0.177,0.198 10 false *e

System Sensors Check

*a: GPS
Display Content
Reception number Displays reception condition of the satellites used to determine vehicle position. Blue: P (In use) System is using GPS signal for location.
Yellow: T (Receiving) System is tracking GPS signal for location.
No color: Not in use System cannot receive GPS signal (searching for GPS signal).
Status Displays reception status of the satellites used to determine vehicle position. OK(H3D) High accuracy 3-dimensional location method is being used.
OK(H2D) High accuracy 2-dimensional location method is being used.
OK(3D) 3-dimensional location method is being used.
OK(2D) 2-dimensional location method is being used.
NG Location data cannot be used.
error Reception error has occurred.
- Any other state.
Measurement ratio Displays the ratio of satellites performing measurements. 3D The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
2D The ratio of satellites performing 2D positioning is displayed.
NG The ratio of satellites not performing measurement is displayed.
Date Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
Position Latitude and longitude information on current position is displayed.

*b: SPD
Display Content
Pulse Count Displays the accumulated number of input pulses beginning when this screen is displayed.
Speed Displays vehicle speed.

*c: Sensor Signal
Display Content Content
Gyro Voltage Displays the output voltage of the gyro sensor. -
0 point Voltage Displays the zero-point voltage of the gyro sensor. -
Relative bearing Displays the output angle of the gyro sensor. The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").

*d: Gyro/Distance correction study situation
Display Content
Gyro/Distance correction study situation Displays learning status of Gyro/Distance correction.

*e: Reset
Display Content
Reset When this switch is pressed and held for 3 seconds or more, the values for the display items of SPD and Sensor Signal are reset and display "0".

i.

When the "System Sensors Check" screen is displayed, check all the sensor signals.

HINT:

This screen is updated once per second.





CHECK DAB RECEPTION (w/ DAB Function)


HINT:
·

The reception condition of Digital Audio Broadcast (DAB) can be checked.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Next Page > DAB Reception Check.


c.
E245217E19
1.735,0.854 1.907,0.854 false 0.135,0.785 0.328,0.957 0.193,0.172 10 *a 0.338,0.875 0.532,0.875 false 2.723,1.172 3.049,1.172 false 2.722,1.326 3.048,1.326 false 1.94,0.776 2.133,0.948 0.193,0.172 10 *b 3.096,1.073 3.288,1.245 0.193,0.172 10 *c 3.099,1.249 3.292,1.421 0.193,0.172 10 *d

DAB Reception Check

Screen Description
Display Content
*a: Up or down switch Enables the channel to be changed to the one to be checked.
*b: Check/STOP switch
·

Check: Starts checking

·

STOP: Stops checking


*c: Antenna connection check Displays DAB antenna connection status as follows:
·

OK: Connected properly

·

NG: Not connected properly

·

-: Not equipped with DAB antenna.


*d: DAB Tuner Reception Level Check Result Description Displays DAB antenna reception levels as follows:
·

111 or more: Font color is black (good reception).

·

110 or less: Font color is red (poor reception).

·

-: Not equipped with DAB antenna.



i.

Select "Check" to start the DAB reception check.


ii.

Check the results displayed when the DAB reception check is completed.




CHECK SPEAKER


HINT:
·

This function is used when checking the speaker wiring and whether the speakers are functioning properly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Turn audio mode on and play any audio source.

HINT:

This audio source will be used for the speaker check.




c.
E268474

Enter the following menus: Failure Diagnosis > System Check > SP Check ON.


d.

Check the speaker wiring and check that the speakers are functioning properly.

HINT:
·

Check that each speaker outputs sound from the selected audio source properly.

·

"SP Check OFF" is displayed during the speaker check.

·

Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

·

More than one speaker may sound simultaneously depending on the speaker wiring.




e.

Sound stops when any of the following conditions are met:

i.

"SP Check OFF" is selected.


ii.

The power switch is turned off.


iii.

Diagnostic mode is turned off.


iv.

The screen is changed to another screen.


v.

Audio mode is turned off.




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the radio and display receiver assembly screen is blacked out.


a.

Check Software Error History.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


v.

When an item is stored for Software Error History, record it before repairing the multi-media module receiver assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.





b.

Clear Software Error History.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause when an optical disc error occurs.


a.

Check Optical Disc Error History.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table (See page (Click here))
Disc damaged/upside down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted upside down.


Cannot determine disc type An unsuitable disc is inserted.
DSP error When an error occurs while decoding MP3/WMA/AAC files.
Some files are corrupt
·

When MP3/WMA/AAC files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA/AAC files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Not available
CD-P Radio and display receiver assembly
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.





b.

Clear Optical Disc Error History.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK VIDEO DEVICE CONNECTION CHECK


HINT:
·

This function is used to detect disconnection of the video devices.

·

In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.



a.

Check Video Device Connection Check.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.


v.

When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

HINT:
·

DTCs are stored when errors are detected.

·

Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.



Video Device Connection Check Screen Description
Error Detected Image Line (Type) Areas to be Checked
H/U - > Separate Display (GVIF) Not available
H/U - > Full RSE (GVIF) Not available
RSE - > Seat Back Display RH (GVIF) Not available
RSE - > Seat Back Display LH (GVIF) Not available
Rear Camera - > H/U (NTSC) NTSC video signal between the radio and display receiver assembly and rear television camera assembly*1
IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
IPA/BGM/PVM ECU - > H/U (NTSC) NTSC video signal between the radio and display receiver assembly and parking assist ECU*2
IPA/BGM/PVM ECU - > H/U (GVIF) Not available

*1: w/ Rear View Monitor System

*2: w/ Intelligent Parking Assist System




b.

Clear Video Device Connection Check.

i.

When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.