Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.


f.

Check the details of the DTC(s) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART).

NOTICE:

The navigation system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Rear View Monitor System* (Click here)

*: w/ Rear View Monitor System





CLEAR DTC (CLEAR USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Clear the DTCs.



START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace malfunctioning parts (for 8 Speakers or w/ Intelligent Parking Assist System) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>AVC-LAN Circuit).

·

After the power switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.



a.

There are 2 methods to start diagnostic mode. Start diagnostic mode by using either of them.


b.

Method 1

i.

Turn the power switch on (IG).


ii.

While pressing and holding the "CAR" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.



c.

Method 2

i.

Turn the power switch on (IG).


ii.

Press the seek/track up panel switch 5 times and then press the seek/track down panel switch 5 times with the screen and audio turned off.

HINT:
·

Diagnostic mode can only be started if the above operation is completed within 15 seconds of the first press of the seek/track up panel switch.

·

If the operation is not completed within 15 seconds of the first press of the seek/track panel switch or fails, turn the screen and audio on and then off again before attempting to start diagnostic mode.





d.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



FAILURE DIAGNOSIS


a.
E268461

The "Failure Diagnosis" screen will be displayed by selecting "Failure Diagnosis" on the "Service Menu" screen.



SYSTEM CHECK


a.
E307632

The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E307633E02
0.313,0.542 0.49,0.542 false 1.208,1.802 1.208,1.156 false 2.052,1.844 2.052,1.615 false 2.896,1.542 3.094,1.542 false 2.844,0.854 3.083,0.854 false 0.125,0.448 0.302,0.615 0.177,0.167 10 false *a 1.125,1.813 1.302,1.979 0.177,0.167 10 false *b 1.979,1.833 2.156,2 0.177,0.167 10 false *c 3.115,1.458 3.292,1.625 0.177,0.167 10 false *d 3.104,0.771 3.281,0.938 0.177,0.167 10 false *e

System check mode screen description

HINT:

When "NCON" is displayed for all devices connected through the AVC-LAN, or when all device names are not displayed, check if there is a short in an AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (for 8 Speakers or w/ Intelligent Parking Assist System) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>AVC-LAN Circuit).


Screen Description
Display Content
*a: Device name list No. 1
·

Device Name List No. 1 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check result Result codes for all devices are displayed.
*c: Memory clear
·

Present and history DTCs and registered connected device names are cleared.

·

Select "Memory CLR" for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

"Recheck" will dim during a system check.


*e: Device name list No. 2
·

Device Name List No. 2 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*a: Device Name List No. 1 Description
Name Component Connection Method
DA Radio and display receiver assembly -
CAMERA-C Parking assist ECU*1 AVC-LAN communication line
DSP-AMP Stereo component amplifier assembly*2 AVC-LAN communication line
NAVI BOX Navigation ECU LVDS communication line

*1: w/ Intelligent Parking Assist System

*2: for 8 Speakers


*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Read DTCs on the "Unit Check Mode" screen.
NCON The device was previously present, but does not respond in diagnostic mode. - Check the power supply circuit of the device.
- Check the LVDS communication line of the device.
- Check the AVC-LAN communication line of the device.
NRES The device responds in diagnostic mode, but gives no DTC information. - Check the power supply circuit of the device.
- Check the LVDS communication line of the device.
- Check the AVC-LAN communication line of the device.

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E268464E20
0.302,0.688 0.677,0.688 false 2.896,1.677 3.125,1.677 false 0.865,1.885 0.865,1.104 false 1.292,0.604 1.229,0.167 1.229,0.167 0.99,0.167 true 1.458,0.438 1.5,0.188 1.5,0.188 1.688,0.188 true 1.698,0.104 1.854,0.281 0.156,0.177 10 false *a 0.771,0.083 0.927,0.26 0.156,0.177 10 false *b 0.083,0.583 0.24,0.76 0.156,0.177 10 false *c 3.146,1.583 3.302,1.76 0.156,0.177 10 false *e 0.74,1.917 0.896,2.094 0.156,0.177 10 false *d

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Diagnosis clear Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E307634

Read the system check result.

i.

If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", no DTCs are present.

·

When proceeding to view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.




ii.

Check the details of the DTC(s) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART).

NOTICE:

The navigation system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Rear View Monitor System* See page (Click here)

*: w/ Rear View Monitor System






DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E307635

Clear DTCs

i.

Select "Memory CLR" for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, use the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.





b.
E307636

Recheck

i.

Select "Recheck".


ii.
E307637

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the power switch off.