Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E286974E04
4.719,2.927 6.646,3.146 1.927,0.219 10 false Navigation Receiver Assembly 4.729,2.031 5.042,2.229 0.313,0.198 10 false L38 4.729,2.427 5.042,2.625 0.313,0.198 10 false L38 4.802,1.844 5.115,2.042 0.313,0.198 10 false 7 4.813,2.24 5.125,2.438 0.313,0.198 10 false 8 5.104,2.042 5.49,2.25 0.385,0.208 10 false TX1+ 5.104,2.427 5.5,2.635 0.396,0.208 10 false TX1- 1.854,2.427 2.229,2.625 0.375,0.198 10 false TX- 1.833,2.042 2.208,2.24 0.375,0.198 10 false TX+ 2.177,1.906 2.49,2.104 0.313,0.198 10 false 8 2.188,2.313 2.5,2.51 0.313,0.198 10 false 7 0.833,2.688 1.146,2.885 0.313,0.198 10 false L31 0.823,2.854 3.26,3.083 2.438,0.229 10 false Stereo Component Amplifier Assembly 4.698,0.469 5.052,0.688 0.354,0.219 10 false L173 4.698,0.865 5.063,1.042 0.365,0.177 10 false L173 5.094,0.469 5.469,0.667 0.375,0.198 10 false TX3+ 5.104,0.885 5.479,1.083 0.375,0.198 10 false TX3- 4.802,0.281 5.115,0.479 0.313,0.198 10 false 7 4.802,0.677 5.115,0.875 0.313,0.198 10 false 8 0.938,1.167 1.25,1.365 0.313,0.198 10 false L64 0.938,1.333 3.615,1.542 2.677,0.208 10 false Parking Assist ECU* 2.188,0.354 2.5,0.552 0.313,0.198 10 false 11 2.188,0.74 2.5,0.938 0.313,0.198 10 false 10 1.865,0.469 2.177,0.667 0.313,0.198 10 false TX+ 1.896,0.865 2.208,1.063 0.313,0.198 10 false TX- 1.042,3.25 3.438,3.458 2.396,0.208 10 false : AVC-LAN Communication Line 3.406,3.281 6.042,3.479 2.635,0.198 10 false *: w/ Intelligent Parking Assist System

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>PRECAUTION).


HINT:

The navigation receiver assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
U191436E02
1.771,1.5 2.104,2.021 false 1.656,1.5 1.375,2.021 false 1.656,3.458 1.979,3.979 false 1.531,3.448 1.25,3.969 false 1.583,0.667 1.885,0.865 0.302,0.198 10 false L38 0.125,0.063 0.427,0.26 0.302,0.198 10 false *a 1.177,2.042 1.542,2.24 0.365,0.198 10 false TX1- 1.979,2.042 2.375,2.24 0.396,0.198 10 false TX1+ 1.542,2.667 1.896,2.865 0.354,0.198 10 false L173 2.031,2.667 2.385,2.865 0.354,0.198 10 false *A 1.083,4 1.448,4.198 0.365,0.198 10 false TX3- 1.865,4.01 2.26,4.208 0.396,0.198 10 false TX3+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-7 (TX1+) - L38-8 (TX1-) Always 60 to 80 Ω
L173-7 (TX3+) - L173-8 (TX3-)* Always 60 to 80 Ω


*: w/ Intelligent Parking Assist System


Text in Illustration
*A w/ Intelligent Parking Assist System
*a Component without harness connected
(Navigation Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the L173 navigation receiver assembly connector (w/ Intelligent Parking Assist System).


c.

Disconnect the L31 stereo component amplifier assembly connector.


d.

Disconnect the L64 parking assist ECU connector (w/ Intelligent Parking Assist System).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-8 (TX+) - L38-7 (TX1+) Always Below 1 Ω
L31-7 (TX-) - L38-8 (TX1-) Always Below 1 Ω
L64-11 (TX+) - L173-7 (TX3+)* Always Below 1 Ω
L64-10 (TX-) - L173-8 (TX3-)* Always Below 1 Ω
L31-8 (TX+) - Body ground Always 10 kΩ or higher
L31-7 (TX-) - Body ground Always 10 kΩ or higher
L64-11 (TX+) - Body ground* Always 10 kΩ or higher
L64-10 (TX-) - Body ground* Always 10 kΩ or higher


*: w/ Intelligent Parking Assist System




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.




OK

REPLACE MALFUNCTIONING PARTS

NG