Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.


WIRING DIAGRAM

E300235E03
0.28,3.253 0.595,3.400 0.314,0.147 10 U3 0.28,3.421 1.777,3.928 1.497,0.507 10 Map Light Assembly (Telephone Microphone Assembly) 5.762,3.253 6.089,3.400 0.326,0.147 10 L38 5.762,3.421 7.108,3.757 1.346,0.335 10 Navigation Receiver Assembly 5.768,1.296 5.872,1.443 0.104,0.147 10 5 5.938,1.389 6.321,1.536 0.383,0.147 10 MIN+ 5.768,0.82 5.872,0.967 0.104,0.147 10 4 5.938,0.913 6.370,1.060 0.432,0.147 10 MACC 5.696,1.773 5.888,1.919 0.192,0.147 10 19 5.938,1.866 6.321,2.012 0.383,0.147 10 MIN- 5.696,2.249 5.888,2.396 0.192,0.147 10 18 5.938,2.342 6.365,2.489 0.427,0.147 10 SGND 5.768,2.74 5.874,2.886 0.106,0.147 10 6 5.938,2.818 6.330,2.965 0.392,0.147 10 SNS2 1.34,2.74 1.522,2.886 0.182,0.147 10 5 1.34,0.82 1.522,0.967 0.182,0.147 10 2 1.34,1.296 1.522,1.443 0.182,0.147 10 3 1.34,1.773 1.522,1.919 0.182,0.147 10 4 0.896,2.819 1.283,2.966 0.387,0.147 10 SNS2 0.834,0.914 1.316,1.060 0.482,0.147 10 MACC 0.844,1.39 1.281,1.537 0.437,0.147 10 MCO+ 0.853,1.866 1.309,2.013 0.456,0.147 10 MCO- 3.26,2.177 3.917,2.324 0.658,0.147 10 (Shielded)

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen.

Refer to Check Microphone in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK).


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.




OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-4 (MACC) - U3-2 (MACC) Always Below 1 Ω
L38-5 (MIN+) - U3-3 (MCO+) Always Below 1 Ω
L38-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L38-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L38-4 (MACC) - Body ground Always 10 kΩ or higher
L38-5 (MIN+) - Body ground Always 10 kΩ or higher
L38-19 (MIN-) - Body ground Always 10 kΩ or higher
L38-18 (SGND) - Body ground Always 10 kΩ or higher
L38-6 (SNS2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
U155183E01
1.58,0.606 1.881,0.787 0.301,0.181 10 L38 0.211,0.148 0.444,0.302 0.232,0.154 10 *a 2.749,2.696 3.195,2.849 0.445,0.154 10 SGND 2.875,1.199 3.321,1.353 0.445,0.154 10 MACC 1.168,2.696 1.516,2.849 0.348,0.154 10 MIN- 2.229,1.996 2.896,2.676 false 2.229,1.72 2.85,1.282 false 2.054,1.996 1.387,2.676 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L38-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-18 (SGND) - Body ground Always Below 1 Ω
L38-19 (MIN-) - Body ground Always Below 1 Ω



c.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)



A

B

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly) (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.
E187117E63
0.16,0.067 0.358,0.265 0.198,0.198 10 *a 1.132,1.654 1.548,1.852 0.415,0.198 10 SNS2 2.303,1.654 2.732,1.852 0.429,0.198 10 MCO- 1.776,1.221 1.403,1.641 false 1.909,1.225 2.501,1.641 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SNS2) - 4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Turn the power switch on (ACC).


b.
U155061E02
1.885,2.094 1.354,2.802 false 2.031,2.094 2.531,2.76 false 1.635,0.583 1.906,0.76 0.271,0.177 10 false U3 0.177,0.073 0.375,0.271 0.198,0.198 10 false *a 0.958,2.792 1.417,2.99 0.458,0.198 10 false MCO- 2.438,2.792 2.865,2.99 0.427,0.198 10 false MCO+

Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the U3 map light assembly (telephone microphone assembly) connector.


c.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B


Text in Illustration
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))



A

B

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).


b.

Check if the same malfunction recurs.


Result:
Result Proceed to
Malfunction does not recur (returns to normal) A
Malfunction recurs B



A

END

B

REPLACE MAP LIGHT ASSEMBLY