Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E339448E16
1.729,0.927 2.208,1.229 0.479,0.302 10 false 1 5.292,0.927 5.771,1.229 0.479,0.302 10 false 16 5.542,1.042 6.021,1.344 0.479,0.302 10 false MUT1 5.292,1.938 5.771,2.24 0.479,0.302 10 false L38 0.656,1.948 1.135,2.25 0.479,0.302 10 false L31 5.281,2.104 6.5,2.594 1.219,0.49 10 false Navigation Receiver Assembly 1.25,1.031 1.729,1.333 0.479,0.302 10 false MUTE 0.635,2.115 1.865,2.646 1.229,0.531 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U155110E01
0.207,0.166 0.366,0.329 0.159,0.163 10 *a 1.595,0.849 1.897,1.012 0.301,0.163 10 L31 2.699,2.413 3.129,2.576 0.430,0.163 10 MUTE 2.399,1.887 2.861,2.381 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L31-1 (MUTE) - Body ground Power switch on (ACC)
Audio system playing
→ Audio system changing modes
2.0 V or higher
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-16 (MUT1) - L31-1 (MUTE) Always Below 1 Ω
L38-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the L38 navigation receiver assembly connector.


b.
U155093E01
1.597,0.672 1.930,0.828 0.333,0.156 10 L38 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 0.586,2.728 0.982,2.883 0.396,0.156 10 MUT1 1.083,2.214 0.904,2.713 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L38-16 (MUT1) - Body ground Power switch on (ACC)
Audio system playing
2.0 V or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY