Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter sub-assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly and the SPD pulse received from the combination meter sub-assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter sub-assembly. The signal is changed to a pulse signal at the transistor in the combination meter sub-assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected
·

Navigation receiver assembly

·

Combination meter sub-assembly

·

Harness or connector

·

Junction connector



WIRING DIAGRAM

E309036E01
0.626,1.485 1.749,1.636 1.123,0.151 10 Skid Control ECU 1.429,0.488 1.720,0.639 0.292,0.151 10 SP1 0.626,1.339 0.945,1.520 0.319,0.181 10 A58 1.783,0.488 1.969,0.636 0.187,0.148 10 11 3.048,7.054 4.268,7.216 1.220,0.162 10 Junction Connector 0.275,2.829 2.595,3.205 2.320,0.376 10 Power Management Control ECU 0.275,2.677 0.565,2.841 0.290,0.164 10 L5 0.095,6.83 0.360,6.993 0.265,0.164 10 A48 0.095,6.992 2.407,7.172 2.312,0.180 10 Headlight Leveling ECU Assembly*4 1.334,6.56 1.747,6.715 0.413,0.154 10 SPDR 1.379,2.385 1.779,2.540 0.400,0.154 10 SPDI 1.783,2.385 1.962,2.544 0.180,0.159 10 14 1.785,6.56 1.968,6.719 0.183,0.159 10 16 3.912,2.385 4.348,2.547 0.436,0.162 10 31*2 3.912,2.231 4.348,2.393 0.436,0.162 10 32*1 2.863,2.385 3.082,2.547 0.219,0.162 10 22 1.805,3.874 2.008,4.035 0.203,0.162 10 24 5.307,6.56 5.524,6.722 0.217,0.162 10 11 3.912,3.87 4.295,4.031 0.383,0.162 10 12*2 3.937,3.716 4.320,3.877 0.383,0.162 10 3*1 2.722,3.87 3.104,4.031 0.383,0.162 10 21*2 2.722,3.716 3.104,3.877 0.383,0.162 10 12*1 3.912,6.562 4.295,6.724 0.383,0.162 10 11*2 3.918,6.396 4.301,6.558 0.383,0.162 10 21*1 2.722,6.562 3.104,6.724 0.383,0.162 10 32*2 2.722,6.396 3.104,6.558 0.383,0.162 10 31*1 5.294,0.488 5.598,0.638 0.304,0.150 10 16 5.294,2.385 5.569,2.535 0.275,0.150 10 15 5.542,0.586 5.741,0.736 0.198,0.150 10 SI 5.542,2.496 5.743,2.647 0.201,0.151 10 +S 4.964,2.755 5.296,2.900 0.332,0.145 10 L27 4.964,2.918 7.091,3.149 2.126,0.231 10 Combination Meter Sub-assembly 0.16,4.172 0.520,4.326 0.360,0.153 10 L146 0.154,4.335 2.598,4.604 2.444,0.269 10 Windshield Wiper Relay Assembly*3 4.948,5.666 7.147,5.961 2.200,0.295 10 Navigation Receiver Assembly*6 0.556,7.599 1.372,7.781 0.817,0.182 10 *1: for LHD 1.746,7.599 2.563,7.781 0.817,0.182 10 *2: for RHD 2.923,7.599 4.698,7.781 1.775,0.182 10 *3: w/ Auto Wiper System 5.416,7.599 6.756,7.781 1.340,0.182 10 *4: w/ LED Headlight 0.556,7.988 2.729,8.170 2.173,0.182 10 *5: for Radio and Display Type 2.923,7.988 5.122,8.170 2.199,0.182 10 *6: for Navigation Receiver Type 1.432,3.874 1.760,4.019 0.328,0.145 10 SPD 5.551,6.56 5.880,6.706 0.328,0.145 10 SPD 4.97,5.515 5.245,5.661 0.275,0.145 10 L38 4.503,6.852 4.778,7.005 0.275,0.153 10 L31 4.547,4.129 4.846,4.284 0.299,0.156 10 L35 4.503,7.012 7.135,7.189 2.632,0.177 10 Stereo Component Amplifier Assembly*7 4.547,4.288 7.078,4.463 2.531,0.176 10 Radio and Display Receiver Assembly*5 2.753,7.054 3.067,7.218 0.314,0.164 10 L70 5.547,3.876 5.860,4.037 0.313,0.162 10 SPD 5.309,3.876 5.483,4.037 0.174,0.162 10 17 5.547,5.221 5.860,5.383 0.313,0.162 10 SPD 5.309,5.221 5.483,5.383 0.174,0.162 10 17 5.416,7.988 7.127,8.170 1.710,0.182 10 *7: for 8 Speakers 2.789,5.233 3.172,5.394 0.383,0.162 10 3*2 2.789,5.067 3.172,5.228 0.383,0.162 10 1*1 1.809,5.223 2.012,5.384 0.203,0.162 10 2 0.164,5.533 0.524,5.686 0.360,0.153 10 R41 0.158,5.696 3.083,6.022 2.925,0.327 10 Tire Pressure Warning ECU and Receiver*8 1.436,5.223 1.765,5.368 0.328,0.145 10 SPD 0.556,8.376 2.949,8.557 2.393,0.182 10 *8: w/ Tire Pressure Warning System

PROCEDURE

1.CHECK SYSTEM SENSORS (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen.

Refer to Check System Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK).


b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).




OK

NG

2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
a.
U155149E01
0.098,0.053 0.255,0.209 0.158,0.155 10 *a 0.883,2.059 1.076,2.215 0.192,0.155 10 +S 2.815,3.566 3.143,3.722 0.328,0.155 10 GND 1.135,3.837 1.347,3.992 0.211,0.155 10 A 0.991,2.016 1.28,1.332 false 1.614,0.387 1.917,0.543 0.303,0.156 10 L27

Check the output waveform.

i.

Remove the combination meter sub-assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L27-15 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)




OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
U155162E01
0.125,0.16 0.282,0.316 0.158,0.155 10 *a 2.468,2.206 2.862,2.362 0.394,0.155 10 SPD 2.971,3.717 3.299,3.872 0.328,0.155 10 GND 1.294,4.009 1.505,4.164 0.211,0.155 10 A 2.612,2.154 2.412,1.487 false 1.655,0.237 1.913,0.393 0.258,0.156 10 L38

Check the input waveform.

i.

Remove the navigation receiver assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L38-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L38-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


OK

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L38-17 (SPD) - L70-3 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L38-17 (SPD) - L70-12 Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-32 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-31 Always Below 1 Ω




OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR