Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E360450E06
0.854,0.583 1.313,0.781 0.458,0.198 10 false USV1 0.896,1.167 1.354,1.365 0.458,0.198 10 false US1- 0.865,1.792 1.323,1.99 0.458,0.198 10 false US1+ 0.844,2.417 1.302,2.615 0.458,0.198 10 false UGD1 0.865,3.031 1.323,3.229 0.458,0.198 10 false USG1 3.281,2.854 4.167,3.094 0.885,0.24 10 false (Shielded) 5.958,0.583 6.417,0.781 0.458,0.198 10 false UPI 5.958,1.156 6.417,1.354 0.458,0.198 10 false UDO- 5.948,1.813 6.406,2.01 0.458,0.198 10 false UDO+ 5.948,2.438 6.406,2.635 0.458,0.198 10 false UJSG 5.958,3 6.417,3.198 0.458,0.198 10 false USG1 1.323,0.479 1.479,0.677 0.156,0.198 10 false 1 1.344,1.021 1.5,1.219 0.156,0.198 10 false 2 1.333,1.615 1.49,1.813 0.156,0.198 10 false 3 1.333,2.292 1.49,2.49 0.156,0.198 10 false 4 1.344,2.885 1.5,3.083 0.156,0.198 10 false 5 5.74,0.5 5.896,0.698 0.156,0.198 10 false 1 5.75,1.031 5.906,1.229 0.156,0.198 10 false 2 5.75,1.646 5.906,1.844 0.156,0.198 10 false 3 5.75,2.313 5.906,2.51 0.156,0.198 10 false 4 5.76,2.917 5.917,3.115 0.156,0.198 10 false 5 0.281,3.438 0.74,3.635 0.458,0.198 10 false L174 0.281,3.594 1.448,3.969 1.167,0.375 10 false No. 1 Stereo Jack Adapter Assembly 1.854,4.177 4.531,4.427 2.677,0.25 10 false : Date Signal (USB Communication Line) 5.76,3.448 6.219,3.646 0.458,0.198 10 false L176 5.76,3.615 6.979,4 1.219,0.385 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>SYSTEM DESCRIPTION).



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>SYSTEM DESCRIPTION).


Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENTED)

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
U191412E01
0.166,2.244 0.340,2.417 0.174,0.174 10 *b 1.517,2.317 1.890,2.468 0.373,0.151 10 L174 0.515,3.337 0.921,3.489 0.406,0.151 10 USV1 0.573,3.787 0.966,3.939 0.394,0.151 10 US1- 0.166,0.076 0.340,0.250 0.174,0.174 10 *a 1.524,0.22 1.886,0.372 0.362,0.151 10 L176 1.52,3.424 0.988,3.424 false 0.571,1.607 1.115,1.759 0.544,0.151 10 UDO+ 2.489,1.412 3.087,1.564 0.598,0.151 10 UDO- 1.572,1.419 1.083,1.66 false 1.839,1.419 2.455,1.482 false 0.583,0.892 1.156,1.043 0.573,0.151 10 UJSG 1.572,1.251 1.085,1.027 false 1.858,1.251 2.489,0.9 false 2.45,3.337 2.910,3.489 0.460,0.151 10 UGD1 2.45,3.61 2.863,3.761 0.413,0.151 10 US1+ 2.45,3.913 2.976,4.064 0.525,0.151 10 USG1 2.431,3.424 1.929,3.424 false 2.521,0.782 3.151,0.933 0.630,0.151 10 UPI 2.273,1.926 2.677,2.077 0.404,0.151 10 USG1 1.638,3.421 0.988,3.835 false 1.808,3.426 2.431,3.685 false 1.766,3.525 2.431,3.975 false 1.77,1.546 2.219,1.964 false

Disconnect the L174 No. 1 stereo jack adapter assembly connector.


b.

Disconnect the L176 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L176-1 (UPI) - L174-1 (USV1) Always Below 1 Ω
L176-2 (UDO-) - L174-2 (US1-) Always Below 1 Ω
L176-3 (UDO+) - L174-3 (US1+) Always Below 1 Ω
L176-4 (UJSG) - L174-4 (UGD1) Always Below 1 Ω
L176-5 (USG1) - L174-5 (USG1) Always Below 1 Ω
L176-1 (UPI) - Body ground Always 10 kΩ or higher
L176-2 (UDO-) - Body ground Always 10 kΩ or higher
L176-3 (UDO+) - Body ground Always 10 kΩ or higher
L176-4 (UJSG) - Body ground Always 10 kΩ or higher
L176-5 (USG1) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Disconnect the L174 No. 1 stereo jack adapter assembly connector.


b.
U191417E01
1.53,0.725 2.010,0.885 0.480,0.161 10 L174 1.929,1.862 2.539,2.074 false 1.52,1.862 0.842,2.081 false 2.576,2.03 2.997,2.176 0.422,0.145 10 UGD1 0.376,2.023 0.797,2.169 0.422,0.145 10 USV1 0.203,0.153 0.405,0.320 0.201,0.166 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L174-1 (USV1) - L174-4 (UGD1) Power switch on (ACC) 5 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.




OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the power switch off.

HINT:

When this malfunction occurs, it is necessary to turn the power switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the power switch on (ACC).


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.


HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.




NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the navigation receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG