Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1AEE  IPA Sensor Communication Circuit  


DESCRIPTION

The parking assist ECU communicates with the No. 1 ultrasonic sensor (for LH side), and the No. 1 ultrasonic sensor (for RH side) via the No. 1 ultrasonic sensor (for LH side). This DTC is stored when the parking assist ECU judges that there is an abnormality in the communication circuit to the No. 1 ultrasonic sensor (for LH side) or the No. 1 ultrasonic sensor (for RH side) that is connected via the for LH side sensor, immediately after the power switch is turned on (READY), or while the sensors are operating (neither park (P) nor reverse (R) is selected and the vehicle is not stopped).

DTC No. DTC Detection Condition Trouble Area
C1AEE Ultrasonic sensor communication bus failure
·

Harness or connector

·

No. 1 ultrasonic sensor (for LH side)

·

No. 1 ultrasonic sensor (for RH side)

·

Parking assist ECU



WIRING DIAGRAM

E188889E07
1.708,0.542 1.906,0.698 0.198,0.156 10 false BI 1.938,0.479 2.063,0.635 0.125,0.156 10 false 1 1.958,0.896 2.083,1.052 0.125,0.156 10 false 3 1.948,1.323 2.073,1.479 0.125,0.156 10 false 5 2.792,0.49 2.917,0.646 0.125,0.156 10 false 2 2.792,0.927 2.917,1.083 0.125,0.156 10 false 4 2.792,1.354 2.917,1.51 0.125,0.156 10 false 6 4.25,0.458 4.375,0.615 0.125,0.156 10 false 1 4.25,0.917 4.375,1.073 0.125,0.156 10 false 3 4.25,1.344 4.375,1.5 0.125,0.156 10 false 5 5.094,0.438 5.281,0.594 0.188,0.156 10 false 1 5.031,0.896 5.219,1.052 0.188,0.156 10 false 19 5.104,1.323 5.271,1.469 0.167,0.146 10 false 2 0.594,1.938 0.781,2.115 0.188,0.177 10 false C1 2.865,1.938 3.146,2.156 0.281,0.219 10 false C2 2.865,2.104 4.333,2.521 1.469,0.417 10 false No. 1 Ultrasonic Sensor (for LH side) 0.604,2.094 2.073,2.479 1.469,0.385 10 false No. 1 Ultrasonic Sensor (for RH side) 5.24,1.927 5.583,2.083 0.344,0.156 10 false L65 5.229,2.104 6.802,2.344 1.573,0.24 10 false Parking Assist ECU 1.708,1 1.906,1.156 0.198,0.156 10 false SI 1.688,1.438 1.885,1.594 0.198,0.156 10 false EI 3,0.552 3.24,0.708 0.24,0.156 10 false BO 3,1.021 3.25,1.177 0.25,0.156 10 false SO 3.021,1.427 3.271,1.583 0.25,0.156 10 false EO 3.99,0.542 4.188,0.698 0.198,0.156 10 false BI 4,1.031 4.198,1.188 0.198,0.156 10 false SI 3.99,1.458 4.188,1.615 0.198,0.156 10 false EI 5.292,0.563 5.698,0.719 0.406,0.156 10 false CSB3 5.281,1 5.615,1.156 0.333,0.156 10 false LIN3 5.292,1.438 5.719,1.594 0.427,0.156 10 false CSG3

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 1 ULTRASONIC SENSOR (for LH SIDE))
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the C2 No. 1 ultrasonic sensor (for LH side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-1 (CSB3) - Body ground Always 10 kΩ or higher
L65-19 (LIN3) - Body ground Always 10 kΩ or higher
L65-2 (CSG3) - Body ground Always 10 kΩ or higher
L65-1 (CSB3) - C2-1 (BI) Always Below 1 Ω
L65-19 (LIN3) - C2-3 (SI) Always Below 1 Ω
L65-2 (CSG3) - C2-5 (EI) Always Below 1 Ω




OK

2.CHECK NO. 1 ULTRASONIC SENSOR (for LH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NO. 1 ULTRASONIC SENSOR (for LH SIDE)
a.

Remove the No. 1 ultrasonic sensor (for LH side) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR>REMOVAL).


b.
E227022E01
1.427,0.478 1.427,1.084 false 1.818,0.478 1.818,1.084 false 2.209,0.478 2.209,1.084 false 1.22,1.2 1.22,1.806 false 1.62,1.2 1.62,1.806 false 2.02,1.2 2.02,1.806 false 1.336,0.272 1.513,0.418 0.177,0.145 10 EI 2.114,0.272 2.291,0.418 0.177,0.145 10 BI 1.708,0.272 1.885,0.418 0.177,0.145 10 SI 1.126,1.836 1.355,1.982 0.229,0.145 10 EO 1.904,1.836 2.146,1.982 0.243,0.145 10 BO 1.497,1.836 1.719,1.982 0.222,0.145 10 SO 0.142,0.105 0.319,0.250 0.177,0.145 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Ultrasonic Sensor (for LH Side))



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR (for LH SIDE) - NO. 1 ULTRASONIC SENSOR (for RH SIDE))

NG

REPLACE NO. 1 ULTRASONIC SENSOR (for LH SIDE)

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR (for LH SIDE) - NO. 1 ULTRASONIC SENSOR (for RH SIDE))
a.

Disconnect the C2 No. 1 ultrasonic sensor (for LH side) connector.


b.

Disconnect the C1 No. 1 ultrasonic sensor (for RH side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-2 (BO) - C1-1 (BI) Always Below 1 Ω
C2-4 (SO) - C1-3 (SI) Always Below 1 Ω
C2-6 (EO) - C1-5 (EI) Always Below 1 Ω
C2-2 (BO) - Body ground Always 10 kΩ or higher
C2-4 (SO) - Body ground Always 10 kΩ or higher
C2-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.REPLACE NO. 1 ULTRASONIC SENSOR (for LH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE NO. 1 ULTRASONIC SENSOR (for LH SIDE)

NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

A

6.REPLACE NO. 1 ULTRASONIC SENSOR (for RH SIDE)

B

END

6.REPLACE NO. 1 ULTRASONIC SENSOR (for RH SIDE)

NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT

A

B

END