The rear height control sensor sub-assembly RH and headlight leveling ECU assembly (for LED headlight) are connected to the parking assist ECU. The parking assist ECU shares the vehicle height signals received from the rear height control sensor sub-assembly RH with the lighting system (auto leveling). The headlight leveling ECU assembly (for LED headlight) supplies power to the rear height control sensor sub-assembly RH via the parking assist ECU. This DTC is stored when the parking assist ECU judges that the power supply voltage for the rear height control sensor sub-assembly RH is not normal.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1627 | ·
Height control sensor voltage is low ·
Height control sensor voltage is high |
·
Harness or connector ·
Headlight leveling ECU assembly (for LED Headlight) ·
Parking assist ECU |
for LED Headlight
for Halogen Headlight
When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).
When the headlight leveling ECU assembly (for LED headlight) is replaced, perform initialization for the lighting system (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION)
If initialization is necessary while performing an inspection, perform initialization first and then proceed to the next step.
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1627 is output | A |
| DTCs are not output | B |
If the power source voltage output by the headlight leveling ECU assembly (for LED headlight) is abnormal, the headlight leveling warning light may come on.
If the DTCs are not output again when rechecking for DTCs, it may have been stored due to a temporarily abnormal voltage.
If DTC C1627 is output frequently, duplicate the problem symptoms and perform the inspection again, even though the DTCs are not output when rechecking for DTCs (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Check vehicle specifications.
| Result | Proceed to |
|---|---|
| for LED Headlight | A |
| for Halogen Headlight | B |
A
B
Disconnect the A48 headlight leveling ECU assembly connector.
Disconnect the L65 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-12 (SBR) - Body ground | Always | 10 kΩ or higher |
| A48-21 (SGR) - Body ground | Always | 10 kΩ or higher |
| A48-12 (SBR) - L65-28 (HB+) | Always | Below 1 Ω |
| A48-21 (SGR) - L65-29 (HGND) | Always | Below 1 Ω |
OK
NG
Reconnect the A48 headlight leveling ECU assembly connector.
Disconnect the L65 parking assist ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-28 (HB+) - L65-29 (HGND) | Power switch on (IG) | 4.75 to 5.25 V |
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
OK
NG
Disconnect the L65 parking assist ECU connector.
Disconnect the S25 rear height control sensor sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-27 (HBL+) - Body ground | Always | 10 kΩ or higher |
| L65-31 (HG1) - Body ground | Always | 10 kΩ or higher |
| L65-27 (HBL+) - S25-3 (SHB) | Always | Below 1 Ω |
| L65-31 (HG1) - S25-1 (SHG) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the L65 parking assist ECU connector.
Disconnect the S25 rear height control sensor sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-30 (HBE+) - Body ground | Always | 10 kΩ or higher |
| L65-31 (HG1) - Body ground | Always | 10 kΩ or higher |
| L65-30 (HBE+) - S25-3 (SHB) | Always | Below 1 Ω |
| L65-31 (HG1) - S25-1 (SHG) | Always | Below 1 Ω |
OK
NG
Reconnect the L65 parking assist ECU connector.
Disconnect the S25 rear height control sensor sub-assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S25-3 (SHB) - S25-1 (SHG) | Power switch on (IG) | 4.75 to 5.25 V |
| *a | Front view of wire harness connector
(to Rear Height Control Sensor Sub-assembly RH) |
OK
NG