Home › Power Source / Network › POWER DISTRIBUTION › POWER MANAGEMENT CONTROL ECU › 2013.08–2014.11
RM2070E _57 Power Source / Network _061935 POWER DISTRIBUTION _0301751 POWER MANAGEMENT CONTROL ECU A

POWER DISTRIBUTION  POWER MANAGEMENT CONTROL ECU  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. WHEN REPLACING POWER MANAGEMENT CONTROL ECU

HV battery learning values are stored in the power management control ECU and ECM to illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning value data from the other ECU and updates the information.

NOTICE:
·

Do not replace the power management control ECU and ECM at the same time as it clears the HV battery learning values. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the power management control ECU or ECM with used ones from other vehicles.



a.

Procedure when replacing both power management control ECU and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either of the ECUs.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the power switch on (READY) and wait for 5 minutes or more.


v.

Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the power switch can be turned on (READY).

HINT:

If the power management control ECU and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 8.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 10.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82877 11.REMOVE ECU INTEGRATION BOX RH (for LHD)

a.
E190800E05
1.135,0.302 1.375,0.573 true 0.708,1.344 1.063,1.344 true 2.448,0.938 2.219,1.073 true 2.5,1.51 2.958,1.885 2.958,1.885 2.49,2.313 false 2.958,1.885 2.5,2.063 false 0.938,0.208 1.156,0.375 0.219,0.167 10 true *A 0.479,1.26 0.698,1.427 0.219,0.167 10 true *A 2.49,0.844 2.708,1.01 0.219,0.167 10 true *B 2.99,1.792 3.208,1.958 0.219,0.167 10 true *C

Disconnect each connector.

Text in Illustration
*A w/ Pre-crash System
*B w/ Dynamic Radar Cruise Control System
*C w/ Advanced Parking Guidance System


b.
E190801

Disengage the 3 clamps.


c.

Remove the bolt and 2 nuts, and ECU integration box RH.


Hide 82878 12.REMOVE ECU INTEGRATION BOX LH (for RHD)

a.
E254094

Disconnect each connector.


b.

Disengage the clamp.


c.
E254095

Remove the bolt and nut, and ECU integration box LH.


Hide 89681A 13.REMOVE POWER MANAGEMENT CONTROL ECU

a.

for LHD:

i.
E190802

Using a screwdriver, disengage the 2 claws and remove the power management control ECU as shown in the illustration.



b.

for RHD:

i.
E254096

Using a screwdriver, disengage the 2 claws and remove the power management control ECU as shown in the illustration.