Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301858 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 2.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

Hide 67911B 3.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 62111C 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 55607 5.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B283355

Disengage the 3 claws and guide.


b.

Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.


Hide 55550 6.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.

Open the glove compartment door.


b.
B283356E03
3,0.583 2.656,0.26 true 1.802,2.615 2.042,2.74 true 2.5,0.177 2.656,0.323 0.156,0.146 10 true *2 1.646,2.531 1.802,2.677 0.156,0.146 10 false *1 3.063,1.469 3.271,1.635 0.208,0.167 10 false (A) 0.417,1.177 0.635,1.365 0.219,0.188 10 true (B)

Disengage the claw and release the glove compartment door stopper sub-assembly.

Text in Illustration
*1 Glove Compartment Door Stopper Sub-assembly
*2 Stopper


c.

Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.


d.
B318019E03
1.031,1.896 1.188,2.042 0.156,0.146 10 false *b 1.865,0.333 2.021,0.479 0.156,0.146 10 false *a 0.729,0.833 1.021,1.125 0.292,0.292 10 false 65°

Open the glove compartment door assembly to approximately 65° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

NOTICE:

Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.


Text in Illustration
*a Closed
*b Opened Approximately 65°


Hide 55054 7.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.
B283358

Disengage the claw to remove the glove compartment door stopper sub-assembly.


Hide 58533F 8.REMOVE CENTER FLOOR CARPET COVER RH

a.
B283379E03
1.375,2.031 1.583,2.24 0.208,0.208 10 true (1) 1.708,1.344 1.906,1.51 0.198,0.167 10 false (2)

Pull the front center floor carpet cover RH in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the center floor carpet cover RH.


Hide 58534H 9.REMOVE CENTER FLOOR CARPET COVER LH

a.
B283380E03
1.969,2.063 2.167,2.229 0.198,0.167 10 true (1) 1.625,1.24 1.844,1.438 0.219,0.198 10 true (2)

Pull the front center floor carpet cover LH in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the center floor carpet cover LH.


Hide 58804A 11.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 58817A 12.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

Hide 14.REMOVE COMBINATION METER ASSEMBLY

a.
B283359

Remove the 4 screws <E>.


b.

Disengage the clamp.


c.

Disconnect each connector to remove the combination meter assembly.


Hide 15.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 16.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)

Hide 17.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B283363

Using a moulding remover, disengage the 11 claws.


b.

Disengage the clamp.


c.

Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.


Hide 55900 18.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 33560 19.REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY

Hide 67914 20.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 21.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 55606 22.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B283364

Remove the 2 screws <E>.


b.

Disengage the 2 claws and guide.


c.

Disconnect each connector.


d.

Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.


Hide 73900 23.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 81260 24.REMOVE GLOVE BOX LIGHT ASSEMBLY

Hide 53601 25.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B283366

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 86101 26.REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)

Hide 86101 27.REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)

Hide 55303B 28.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

a.
B283381

Disconnect the connector.


b.
E190806

Disengage the claw and disconnect the connector as shown in the illustration.


c.

Disengage each clamp.

B313757E02
1.125,3.604 0.698,3.958 true 0.521,3.906 0.677,4.052 0.156,0.146 10 false *1

Text in Illustration
*1 Room Temperature Sensor - -


d.

Disengage the 2 claws to disconnect the room temperature sensor from the lower instrument panel sub-assembly.


e.

Disengage the 2 claws.


f.

Remove the 2 bolts <A>, 10 screws <C> and screw <D> and lower instrument panel sub-assembly.

B283368E03
2.833,3.313 2.99,3.458 0.156,0.146 10 false *2 3.865,3.396 4.031,3.604 0.167,0.208 10 true *3 5.292,4.469 5.448,4.615 0.156,0.146 10 false *1 1,2.396 1.156,2.542 0.156,0.146 10 false *1 2.156,2.99 2.313,3.135 0.156,0.146 10 false *2 1.104,2.156 1.271,2.323 0.167,0.167 10 true *2 0.688,0.875 0.854,1.042 0.167,0.167 10 true *2 1.198,0.573 1.365,0.74 0.167,0.167 10 true *2 2.021,0.76 2.188,0.938 0.167,0.177 10 true *2 3.625,1.104 3.781,1.271 0.156,0.167 10 true *2 3.813,1.667 3.969,1.813 0.156,0.146 10 true *2 4.427,2.063 4.583,2.208 0.156,0.146 10 true *2 5.219,2.417 5.375,2.563 0.156,0.146 10 true *2

Text in Illustration
*1 Bolt <A> *2 Screw <C>
*3 Screw <D> - -


Hide 55303B 29.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

a.

Disengage the 2 claws to disconnect the DLC3.

B274939E02
6.177,3.75 6.177,4.323 true 4.063,4.031 3.135,4.292 true 2.958,4.24 3.115,4.385 0.156,0.146 10 true *2 6.094,4.354 6.25,4.5 0.156,0.146 10 false *1

Text in Illustration
*1 DLC3 *2 Room Temperature Sensor


b.

Disengage each clamp.


c.

Disengage the 2 claws to disconnect the room temperature sensor from the lower instrument panel sub-assembly.


d.

Remove the 2 bolts <A>, 10 screws <C> and screw <D> and lower instrument panel sub-assembly.

B274940E02
1.688,2.344 1.844,2.49 0.156,0.146 10 true *2 3,3.479 3.156,3.625 0.156,0.146 10 true *3 1.708,4.448 1.865,4.594 0.156,0.146 10 false *1 2.49,2.052 2.646,2.198 0.156,0.146 10 true *2 2.885,1.885 3.042,2.031 0.156,0.146 10 true *2 3.292,1.115 3.448,1.26 0.156,0.146 10 true *2 4.052,3.313 4.208,3.458 0.156,0.146 10 false *2 4.781,2.979 4.938,3.125 0.156,0.146 10 false *2 4.885,0.76 5.042,0.906 0.156,0.146 10 true *2 5.708,0.542 5.865,0.688 0.156,0.146 10 true *2 6.219,0.875 6.375,1.021 0.156,0.146 10 true *2 5.802,2.156 5.958,2.302 0.156,0.146 10 true *2 5.896,2.354 6.052,2.5 0.156,0.146 10 false *1

Text in Illustration
*1 Bolt <A> *2 Screw <C>
*3 Screw <D> - -