Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2012.03–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and transmission control ECU assembly stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2786 No communication between transmission control ECU assembly and certification ECU (smart key ECU assembly) for 10 seconds or more.
·

Transmission control ECU assembly

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector

·

P CON MAIN fuse



WIRING DIAGRAM

B228565E09
0.885,2.579 2.448,2.920 1.563,0.341 10 Certification ECU (Smart Key ECU Assembly) 4.014,2.579 5.374,2.920 1.360,0.341 10 Transmission Control ECU Assembly 0.885,2.411 1.164,2.564 0.279,0.154 10 L62 3.908,1.468 4.187,1.621 0.279,0.154 10 A24 1.81,1.468 2.086,1.614 0.276,0.147 10 LIN 4.247,1.468 4.524,1.614 0.276,0.147 10 LIN 5.499,1.243 6.377,1.399 0.878,0.156 10 P CON MAIN 4.733,1.066 5.121,1.222 0.387,0.156 10 BATT 4.845,1.538 5.122,1.693 0.276,0.156 10 E01 4.845,1.916 5.122,2.072 0.276,0.156 10 E02 5.191,1.928 5.469,2.081 0.279,0.154 10 A24 5.191,1.528 5.469,1.682 0.279,0.154 10 A24 5.191,1.071 5.469,1.224 0.279,0.154 10 A23 4.371,0.391 5.869,0.547 1.498,0.156 10 from Auxiliary Battery 0.666,3.464 2.282,3.620 1.617,0.156 10 : LIN Communication Line 2.164,1.327 2.352,1.481 0.188,0.154 10 29 3.931,1.284 4.119,1.437 0.188,0.154 10 24 5.227,0.877 5.415,1.031 0.188,0.154 10 15 5.276,1.361 5.388,1.514 0.112,0.154 10 6 5.276,1.753 5.388,1.907 0.112,0.154 10 5

CAUTION / NOTICE / HINT

HINT:

Although "No Response from Steering Lock ECU" is displayed on the GTS, this message is shown if the certification ECU (smart key ECU assembly) cannot communicate with the transmission control ECU assembly.


NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, register the key.

·

If the transmission control ECU assembly is replaced, register the ECU code.

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the A23 and A24 transmission control ECU assembly connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-6 (E01) - Body ground Always Below 1 Ω
A24-5 (E02) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
A23-15 (BATT) - Body ground Power switch off 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - TRANSMISSION CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-29 (LIN) - A24-24 (LIN) Always Below 1 Ω
L62-29 (LIN) - Body ground Always 10 kΩ or higher




OK

3.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
a.

Replace the transmission control ECU assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>TCM>REMOVAL).



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2786 is not output.




OK

END (TRANSMISSION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)